锻压技术

基于正交试验的不锈钢冲压模具磨损分析及优化

英文标题：Wear analysis and optimization on stainless steel stamping die based on orthogonal test

作者：谢晖赵笠程王杭燕黄康

单位：湖南大学

分类号：TG76

出版年,卷(期):页码：2017,42(10):132-137

摘要：

模具磨损是影响模具使用寿命的重要因素之一，将正交试验法与冲压数值模拟相结合，综合评估了不锈钢冲压模具的模具硬度、摩擦系数和冲压速度对冲压模具磨损的影响，并确定最优影响因素组合。以汽车消音器外壳冲压模具为例，建立了冲压件和模具的计算机辅助工程模型，分别运用正交试验及参数试验方法进行仿真计算方案的设计。通过正交试验分析，获得了各因素对模具磨损的影响按从大到小的顺序依次为模具硬度、摩擦系数、冲压速度；同时，通过极差、方差等分析，发现模具硬度和摩擦系数对模具的磨损有显著影响。由两种试验方法对比发现，正交试验获得的磨损量比参数试验获得的磨损量减少了61.4%，最优参数组合为模具硬度65 HRC、摩擦系数0.08、冲压速度200 mm·s-1，该优化组合为减少模具的磨损量提供了一种参考。

Die wear is one of the important factors affecting the service life of die. The influences of die hardness, friction coefficient and stamping speed of stainless steel stamping dies on stamping die wear were evaluated comprehensively by combining orthogonal test with numerical simulation, and the optimal combination of factors was determined. For the stamping die of automobile muffler shell, a computer aided engineering model of stamping parts and dies was established, and the design of simulation scheme was conducted by orthogonal test and parameter test respectively. Through the orthogonal test analysis, the influences of various factors on die wear were obtained in the order from big to small as follows die hardness, friction coefficient, stamping speed, and the die hardness and friction coefficient have a significant effect on die wear by the range analysis and variance analysis. Furthermore, comparing the parameter test with the orthogonal test, the amount of wear obtained by the orthogonal test is 61% lower than that obtained by the parameter test. The optimal combination is that die hardness of 65 HRC, friction coefficient of 0.08 and stamping speed of 200 mm·s-1 respectively. Thus, it provides a reference for reducing the die wear.

基金项目：

国家科技重大专项（2014ZX04002-071）；2016年湖南省战略性新兴产业科技攻关项目（2016GK4008）

作者简介：谢晖（1971-），男，博士，教授，E-mail：danielxie@163.com；通讯作者：赵笠程（1994-），男，硕士研究生，E-mail：786548109@qq.com

参考文献：

[1]阳春启，杨旭静. 基于不等截面拉延筋的冲压工艺及回弹控制[J]. 湖南大学学报: 自然科学版, 2010, 37(4): 27-31.

Yang C Q, Yang X J. Forming process based on non-uniform section drawbead and its application in springback control[J]. Journal of Hunan University: Natural Sciences, 2010, 37(4): 27-31.

[2]王雷刚,黄瑶,孙宪萍,等.基于修正Archard磨损理论的挤压模具磨损分析[J]. 密封与润滑, 2006, 31(3): 10-12.

Wang L G, Huang Y, Sun X P, et al.Wear analysis of extrusion die based on Archard′s theory[J]. Lubrication Engineering, 2006, 31(3): 10-12.

[3]周杰,赵军,安治国.对热挤压模磨损规律及磨损对模具寿命的影响[J]. 中国机械工程, 2007, 18(17): 2112-2115.

Zhou J, Zhao J, An Z G. Wear rule and effects on the die service life during hot extrusion[J]. China Mechanical Engineering, 2007, 18(17): 2112-2115.

[4]吴延昭, 王华君, 王华昌, 等. 长寿命热锻模的磨损分析与寿命预测[J]. 锻压技术, 2011, 36(2):90-94.

Wu Y Z, Wang H J, Wang H C, et al. Wear analysis and service life prediction for long life hot forging die[J]. Forging & Stamping Technology,2011, 36(2): 90-94.

[5]史双喜,李福涛. 基于Deform的精冲模具磨损特性研究[J]. 密封与润滑, 2015, 40(7): 89-92.

Shi S X, Li F T. Research on fine blanking die wear based on Deform[J]. Lubrication Engineering, 2015, 40(7): 89-92.

[6]Jahamir S, Suh N P, Abrahamson II E P. The delamination theory of wear and the wear of a composite surface[J]. Wear, 1975, 32(1): 33-49.

[7]彭必友，殷国富，傅建, 等.铝型材挤出速度对模具磨损程度的影响[J].中国有色金属学报，2007, 17(9)：1453-1458．

Peng B Y, Yin G F, Fu J, et al. Effect of extrusion velocity to wear degree of aluminum profile[J]. The Chinese Journal of Nonferrous Metals, 2007, 17(9): 1453-1458．

[8]Eriksen M. The influence of die geometry on tool wear in deep drawing [J]. Wear, 1997, 207(1/2): 10-15.

[9]谢晖,李江曼, 王诗恩, 等. 超高强钢板冲压模具磨损CAE分析研究与应用[J].湖南大学学报: 自然科学版, 2015, 42(8): 15-21．

Xie H, Li J M, Wang S E, et al. Research and application of die wear CAE analysis of ultra high strength steel stamping[J]. Journal of Hunan University: Natural Sciences., 2015, 42(8): 15-21．

[10]张亚龙,徐新成,栾怀超,等.温镦挤模具磨损失效分析[J]. 热加工工艺, 2014, 43(5): 225-230．

Zhang Y L, Xu X C, Luan H C, et al. Failure analysis on wear of warm upset-extrusion die[J]. Hot Working Technology, 2014, 43(5): 225-230．

[11]郑伟刚,尹存宏,杨宁,等.基于Archard的正挤压模具磨损模拟分析与研究[J]. 锻压技术, 2013, 10(5): 148-151.

Zheng W G, Yin C H, Yang N, et al. Die wear simulation of forward extrusion process based on Archard theory [J]. Forging & Stamping Technology, 2013, 10(5): 148-151.

[12]龚小涛，杨帆，陈荷. 基于 Archard 模型的热摆辗模具磨损研究[J]. 锻压技术, 2015，40(10):119-129.

Gong X T, Yang F, Chen H. Research on wear of hot rotary forging die based on Archard′s model[J]. Forging & Stamping Technology, 2015，40(10):119-129.

[13]杨晓蕾，吴淑芳.基于Archard 磨损理论的螺旋伞齿轮精锻成形模具磨损分析[J]. 长春大学学报, 2014, 24(4): 451-454．

Yang X L, Wu S F. Analysis on wear of forming die for precision forging of spiral bevel gears based on archard wear theory[J]. Journal of Changchun University, 2014, 24(4): 451-454．

服务与反馈：

【文章下载】【加入收藏】