锻压技术

飞机蒙皮振动辅助拉伸成形工艺分析

英文标题：Analysis on vibration-assisted stretch forming of aircraft skin panel

作者：柏玲磊陈梁玉赵坤民

分类号：TG386

出版年,卷(期):页码：2017,42(11):18-25

摘要：

拉伸成形结束后，由于残余应力的存在导致蒙皮零件产生较大的回弹，会严重影响蒙皮的使用质量。基于回弹产生的原因，从工件的应力-应变机制阐述了振动减小残余应力的机理，提出了一种振动辅助飞机蒙皮拉伸成形的新工艺方法，给出了该工艺的主要参数——频率、振幅在应用选择上的依据条件及实际运用中可选择的合理范围。以飞机前缘蒙皮拉伸成形为例，通过数值仿真模拟，分析了施加振动对成形蒙皮零件回弹的影响以及频率、振幅对改善回弹的影响，并通过实验加以验证。结果表明，在飞机蒙皮拉伸成形过程中，施加振动可以更加有效地减小零件的回弹，当选取的工艺参数频率为30 Hz左右、振幅在1.5 mm左右时回弹值最小，效果最佳。

After stretch forming, the residual stress in the formed panel causes springback, which seriously affects the assembly quality. Based on the cause of springback, the mechanism of residual-stress relief through vibration was described by the stress-strain mechanism of workpiece, and an vibration-assisted stretch forming of aircraft skin panel was proposed. Then, The basis condition of frequency and amplitude for the main parameters of process in the application and the reasonable range of practical choice in the practical application were given. Therefore, for the stretch forming of aircraft front edge skin panel, the influences of vibration on the springback and the frequency and amplitude on the springback modification were analyzed by numerical simulation and verified by the experiments. The results show that adding vibration in the stretch forming process of aircraft skin panel can reduce springback effectively, and when the frequency and amplitude are 30 Hz and 1.5 mm respectively, the sprinback is the minimum.

基金项目：

国家自然科学基金资助项目(11472072)

作者简介：柏玲磊（1991-），男，硕士研究生 E-mail：hfutllbai@sina.com 通讯作者：赵坤民（1971-），男，博士，教授，博士生导师，国家“千人计划”专家 E-mail：kmzhao@dlut.edu.cn

参考文献：

[1]胡成武, 胡泽豪. 冲压工艺与模具设计[M].长沙:中南大学出版社,2012.

Hu C W, Hu Z H. Stamping Process and Die Design[M]. Changsha: Central South University Press, 2012.

[2]张彦敏, 周贤宾.飞机蒙皮拉伸成形工艺参数优化[J].航空学报, 2006, 27(6):1203-1208.

Zhang Y M, Zhou X B. Parameter optimization in aircraft skin stretch forming process[J]. Acta Aeronautica Et Astronautica Sinica, 2006, 27(6): 1203-1208.

[3]He D H, Li D S, Li X Q, et al. Optimization on springback reduction in cold stretch forming of titanium-alloy aircraft skin[J]. Transactions of Nonferrous Metals Society of China, 2010, 20(12):2350-2357.

[4]晋坤, 孙秀京, 尹苹,等. 航天用铝合金蒙皮拉形工艺研究[J]. 锻压技术, 2015, 40(8):47-51.

Jin K, Sun X J, Yin P, et al. Study on stretch forming of aluminum alloy skin for aerospace[J]. Forging & Stamping Technology, 2015, 40 (8): 47-51.

[5]温彤, 斐春雷, 李昌坤. 塑性成形过程的振动应用技术[J]. 热加工工艺,2009,38(1):120-123.

Wen T, Fei C L, Li C K. Application of vibration in plastic forming process[J]. Hot Working Technology, 2009, 38(1): 120-123.

[6]Jafari M S, Azizmoradi M, Emami M M. Stress relief and material properties improvement through vibration vs. common thermal method[J]. Journal of Mechanics, 2012, 4(2): 170-176.

[7]谭喜平, 宋东福, 郑开宏.锰和硼结合振动对再生铝组织和力学性能的影响[J].稀有金属, 2015, 39(12):1076-1082.

Tan X P, Song D F, Zheng K H. Microstructure and mechanical properties of recycled aluminum alloy by Mn, B and mechanical vibration [J]. Chinese Journal of Rare Metals, 2015, 39 (12): 1076-1082.

[8]芦亚萍. 振动消除残余应力机理分析及试验研究[D]. 杭州: 浙江大学, 2002.

Lu Y P. Mechanism Analysis and Experimental Study on Residual Stress of Vibration Elimination[D]. Hangzhou: Zhejiang University, 2002.

[9]焦馥杰, 茅鹏, 沈瑜书. 振动时效机理研究[J]. 焊接学报, 1992,4(3):169-174.

Jiao F J, Mao P, Shen Y S. Investigation of mechanism of vibration ageing[J]. Transactions of the China Welding Institution, 1992, 4(3): 169-174.

[10]王家鹏. 超声振动辅助成形本构模型理论及实验研究[D]. 上海: 上海交通大学, 2015.

Wang J P. Theoretical and Experimental Study on Constitutive Model of Ultrasonic Vibration Assisted Forming[D]. Shanghai: Shanghai Jiao Tong University,2015.

[11]程涛, 刘艳雄, 华林. 超声波振动辅助精冲成形工艺研究[J].锻压技术, 2016, 41(4):25-30.

Cheng T, Liu Y X, Hua L. Research on the technology of ultrasonic vibration assisted fine blanking process[J]. Forging & Stamping Technology, 2016, 41 (4): 25-30.

[12]Kriechenbauer S, Mauermann R, Muller P. Deep drawing with superimposed low-frequency vibrations on servo-screw presses[J]. Procedia Engineering, 2014, 81:905-913.

[13]Huang Y M, Wu Y S, Huang J Y. The influence of ultrasonic vibration-assisted micro-deep drawing process[J]. The International Journal of Advanced Manufacturing Technology, 2014, 71(5): 1455-1461.

服务与反馈：

【文章下载】【加入收藏】