锻压技术

罩盖液压拉深成形的数值模拟分析

英文标题：Numerical simulation analysis on hydraulic drawing of cover

作者：顾勇吴小涛袁鸿斌勾治践

分类号：TG386

出版年,卷(期):页码：2017,42(11):47-49

摘要：

板料液压成形是制造难成形件的一种有效方法。分析了罩盖液压拉深成形的工艺性，通过运用Dynaform板料成形软件，对罩盖零件的液压拉深成形过程进行了数值模拟，获得了成形后的零件成形极限图和变薄率分布图，并分析了其拉深成形过程。研究结果表明，采用初始设定的参数，罩盖在液压拉深过程中，最大变薄率约为18.27%，小于25%，成形效果良好，不容易破裂。采用模拟中使用的各成形条件，通过液压拉深实验能拉深出合格的成形零件，验证了模拟过程的正确性。

Sheet hydro-forming is an effective method for manufacturing complicated parts. The manufacturability of hydraulic drawing of cover was analyzed,and the hydraulic drawing process of cover was simulated and analyzed by software Dynaform, and its FLD and thinning rate distribution were obtained. The results show that the maximum thinning rate of cover in the process of hydraulic drawing is about 18.27% and less than 25% by adopting initial designed parameters, and the forming effect is excellent without crack. Thus, the qualified drawing parts are manufactured through hydraulic drawing experiment under the adopted condition in simulation, which verifies the correctness of simulation process.

基金项目：

2015年杭州市属高校产学对接特需专业（机制）建设项目（杭教育师[2015]7号）

作者简介：顾勇（1983-），男，博士研究生，讲师 E-mail：gy2018@hznu.edu.cn

参考文献：

[1]Lang L H, Wang Z R, Kang D C, et al. Hydroforming highlights: Sheet hydroforming and tube hydroforming [J].Journal of Materials Processing Technology, 2004, 151 (1/3):165-177.

[2]Palumbo G, Piccininni A, Guglielmi P, et al. Warm hydroforming of the heat treatable aluminium alloy AC170PX[J].Journal of Manufacturing Processe,2015,20: 24-32.

[3]Shinde R A，Dr BTP，Joshi K N. Optimization of tube hydroforming process (without axial feed) by using FEA simulations [J].Procedia Technology, 2016,23:398-405.

[4]Kim H S，Sumption M D，Bong H J, et al. Development of a multi-scale simulation model of tube hydroforming for superconducting RF cavities[J]. Materials Science & Engineering A, 2017, 679: 104-115.

[5]Chen Y Z, Liu W, Zhang Z C, et al. Analysis of wrinkling during sheet hydroforming of curved surface shell considering reverse bulging effect [J].International Journal of Mechanical Sciences, 2016,120: 70-80.

[6]王宁华，杨连发.基于液压胀形实验及增量理论构建管材本构关系[J].锻压技术，2015,40（2）：133-138.

Wang N H, Yang L F. Determination of constitutive relationship of tubular materials based on incremental theory and hydraulic bulge test [J].Forging & Stamping Technology,2015, 40（2）：133-138.

[7]王金雷，卫原平，阮雪榆.抛物体形拉深件液压成形工艺的数值模拟[J].塑性工程学报，2001,8(4):55-58.

Wang J L, Wei Y P, Ruan X Y. Numerical simulation of the hydromechanical deep drawing of parabola workpieces[J].Journal of Plasticity Engineering,2001,8(4):55-58.

[8]陈淑婉，蒋敏，詹艳然，等.行李箱内板拉深压边力曲线的优化[J].制造技术与机床，2014,（1）:163-168.

Chen S W, Jiang M, Zhan Y R, et al. Optimization of blank-holder force curve for the deep drawing of trunk lid inner panel [J]. Manufacturing Technology & Machine Tool, 2014,（1）:163-168.

服务与反馈：

【文章下载】【加入收藏】