锻压技术

Stavax ESR钢洗衣机面板模具开裂原因分析

英文标题：Analysis on the causes of mold cracking for steel Stavax ESR washing machine

作者：金林奎欧海龙黄持伟阮育煌邹文奇

单位：广东省东莞市质量监督检测中心国家模具产品质量监督检验中心东莞市奕东电子有限公司

分类号：TG147

出版年,卷(期):页码：2017,42(11):136-143

摘要：

针对Stavax ESR钢洗衣机面板模具开裂问题，对模具失效件进行断口扫描电镜及微区能谱分析，以及采用金相显微镜对材料基体组织进行检测，综合检测结果，最终确定造成模具早期开裂的内在原因，是由于组织中沿晶界残留未溶颗粒状及薄片状碳化物，材料强度急剧降低，脆性显著增大。模具在热加工过程中碳化物沿晶界析出形成网状碳化物，在热处理加热保温过程中，网状碳化物经过固溶和聚集，形成未溶颗粒状及薄片状碳化物。热处理加热过程的热应力以及淬火过程的组织应力，导致未溶颗粒状及薄片状碳化物周围产生内裂纹。模具冷却水孔的机加工过程，使沿晶开裂特征的内裂纹显露出来。模具服役承载时产生的工作应力，促使裂纹的进一步萌生和扩展。

For the cracking in the panel mold of steel Stavax ESR washing machine, the fracture failure in the mold was studied by fracture scanning electron microscopy and micro-zone energy spectrum analysis, and the matrix structure was detected by metallographic microscope. The internal cause of mold cracking was residual undissolved granular and flaky carbide along the grain boundary in the organization, the sharp decrease of material strength, and the remarkable increase of brittleness. In the hot-rolling process of mold, mesh carbide was separated out along the grain boundary, and undissolved granular and flaky carbide were formed by the solid solution and aggregation during the heat treatment and heating process. Therefore, the thermal stress of heating process and the microstructural stress of quenching process resulted in internal cracks around the undissolved granular and flaky carbides. Furthermore, the cracks with intergranular cracking characteristics were exposed in the machining process of mold cooling water hole, and the work stress produced by the load of mold promoted a further crack initiation and propagation.

基金项目：

广东省东莞市产学研合作项目（201550910500294）

作者简介：金林奎(1966-)，男，学士，高级工程师 E-mail：jinlinkui@foxmail.com；jlk@gddqt.com

参考文献：

[1]吴振海.常用模具钢热处理性能[M].北京：中国水利水电出版社，2006.

Wu Z H. Heat Treatment Performance for Commonly Used Die Steel[M]. Beijing: China Water & Power Press, 2006.

[2]钟群鹏，赵子华.断口学[M].北京：高等教育出版社，2006.

Zhong Q P, Zhao Z H. Fractography[M]. Beijing: High Education Press, 2006.

[3]崔约贤，王长利.金属断口分析[M].哈尔滨：哈尔滨工业大学出版社，1998.

Cui Y X, Wang C L. Analysis of Metal Fracture[M]. Harbin: Harbin Institute of Technology Press,1998.

[4]张新和，庄新村，赵幸锋, 等.冷锻模具寿命评估方法研究现状与进展[J].锻压技术，2016 ,41(8):7-11.

Zhang X H, Zhuang X C, Zhao X F, et al. Research status and advances of life assessment method for cold forging die[J].Forging & Stamping Technology，2016 ,41(8):7-11.

[5]温亚辉，李长亮，张清, 等.粉末粒度对钨钼双金属性能影响[J].稀有金属，2016 ,40(11):1188-1192 .

Wen Y H, Li C L, Zhang Q，et al. Properties of W/Mo bimetal with different powder particle sizes[J].Chinese Journal of Rare Metals，2016 ,40(11):1188-1192 .

[6]GB/T 1299—2014, 工模具钢[S].

GB/T 1299—2014, Tool and mould steels [S].

[7]马鹏飞,李美兰,戈晓岚.热处理技术[M].北京：化学工业出版社，2008.

Ma P F, Li M L, Ge X L. Heat Treatment Technology[M]. Beijing: Chemical Industry Press,2008.

[8]史美堂.常用模具钢热处理性能[M].上海：上海科学技术出版社，1981.

Shi M T. Heat Treatment Performance for Commonly Used Die Steel[M]. Shanghai: Shanghai Scientific & Technical Publishers, 1981.

服务与反馈：

【文章下载】【加入收藏】