锻压技术

矩形件正反拉延成形工艺研究及变工序模具设计

英文标题：Research on forwardreverse drawing of rectangular parts and variableprocess die design

作者：李钦生何俊俞蓓刘彦春丁响林

单位：安徽机电职业技术学院

分类号：TG386

出版年,卷(期):页码：2018,43(6):37-41

摘要：

在正反拉延成形中，拉延次序是影响拉延成形是否成功的一个重要因素。针对某一底部具有“反鼓包”特殊结构的矩形件，根据其成形工艺特点，拟定3种不同拉延成形工艺方案，即对矩形件正反两个方向分别采用不同次序进行拉延。首先利用Dynaform软件分别按不同拉延方案对矩形件进行数值模拟，再通过对3种方案的模拟结果进行比较分析，从而得出最佳成形方案。为了验证模拟的准确性，设计与制造出实验用的变工序拉延复合模具。通过分别对这3种方案进行实验验证，证明了模拟结果的正确性和“先反向后正向拉延”方案的可行性。

The order of drawing is an important factor that influences the success of forming in the forwardreverse drawing. Then, for a special rectangle part with an ‘antidrum’ on its bottom, three different drawing schemes were developed according to its forming characteristics, namely, the two directions of the rectangular part were drawn in different orders. At first, the rectangular part was simulated by software Dynaform in different drawing schemes respectively, and then, the simulation results of three schemes were compared and analyzed to get optimum forming scheme. Finally, a kind of variableprocess composite drawing die was designed and made to verify the correctness of the simulations. The result shows that the correctness of the simulation results and the feasibility of ‘first reverse then forward drawing’ scheme are proved by experiments in the three schemes respectively.

基金项目：

安徽高校自然科学研究重点项目（KJ2018A0871，KJ2015A441)

李钦生(1975-)，男，硕士，讲师；Email：ahjdlqs@126.com

参考文献：

［1］李钦生，陈炜，黄振荣，等.汽车顶盖拉延成形研究及工艺参数优化
［J］.锻压技术，2011，36(5)：19-23.

Li Q S,Chen W,Huang Z R,et al.Research on forming process of automobile cover & technological parameter optimization
［J］.Forging & Stamping Technology,2011,36(5)：19-23.

［2］彭华.基于成形极限图的板料多步冲压工艺优化
［D］. 镇江：江苏大学，2005.

Peng H.Processes Optimization in Sheet Metal Multiplestep Forming Based on FLD
［D］.Zhenjiang: Jiangsu University, 2005.

［3］陈炜，陶宏之.基于数值模拟的板料多道次拉深工艺研究
［J］.农业机械学报，2002,33（4)：95-98.

Chen W,Tao H Z.Research on process of multistage sheet metal drawing based on numerical simulation
［J］.Journal of Agricultural Machinery,2002,33(4)：95-98.

［4］白有俊，刘世豪，苏思，等.汽车侧壁上外板冲压成形过程仿真及实验
［J］.锻压技术，2017，42(9)：25-28.

Bai Y J,Liu S H,Su S, et al.Stamping process simulation and experiment of automotive side wall plate
［J］.Forging & Stamping Technology,2017,42(9):25-28.

［5］张东民，刘铭心，盛育东，等.汽车座椅外侧板单动拉延成形工艺分析及优化
［J］.锻压技术，2017，42(6)：61-64.

Zhang D M,Liu M X,Sheng Y D, et al.Process analysis and optimization on single drawing for outer panel of automobile seat
［J］.Forging & Stamping Technology,2017,42(6)：61-64.

［6］Zhao L, Sowerby R, Sklad M P. A theoretical and experimental investigation of limit strains in sheet metal forming
［J］. International Journal of Mechanical Sciences, 1996, 38(38):1307-1317.

［7］魏公际，齐文艺，臧顺来，等.盒形件法兰起皱临界压边力的试验研究
［J］.锻压技术，2008，33(4)：22-26.

Wei G J,Qi W Y,Zang S L,et al.Experimental research on critical blank holder force of rectangular box flange wrinkling
［J］.Forging & Stamping Technology,2008,33(4)：22-26.

服务与反馈：

【文章下载】【加入收藏】