锻压技术

基于DYNAFORM的板式换热器板片的成形模具设计

英文标题：Forming die design of plate type heat exchanger plate based on DYNAFORM

作者：王言德胡心平曲云山

单位：齐鲁工业大学

分类号：TG385.2

出版年,卷(期):页码：2018,43(6):108-112

摘要：

板式换热器板片的成形质量与生产板片的成形模具设计及工艺参数有着密切关系，模具设计及工艺参数设置的不合理会造成板片过度减薄甚至开裂。为了改善板式换热器板片的成形质量，基于DYNAFORM仿真分析技术，对一款板式换热器板片进行了成形仿真研究。依据4组仿真结果的对比，对凸凹模间隙、冲压速度、摩擦系数等工艺参数进行了设计和选取。通过分析4组板片的成形极限图和厚度变化云图，并采用厚度减薄率来评价成形结果，得到了其最优的成形效果。仿真结果表明：冲压速度为2000 mm·s-1，摩擦系数为0.125，凸凹模间隙为0.87 mm时，成形效果最好。

The forming quality of the plate type heat exchanger plate (PTHE) is closely related to the design of forming die and process parameters, and unreasonable die design and process parameters will cause the plate to thin excessively or even crack. In order to improve the forming quality of PTHE, the forming process of a PTHE was simulated by the DYNAFORM, and process parameters of punch including the clearance between punch and die, stamping speed and friction coefficient were selected and designed based on four sets of simulation results. By analyzing the forming limit diagrams and thickness nephograms, the forming results were evaluated by thickness reduction ratio, and the optimal forming effect was obtained. The simulation results show that the best forming result is obtained with stamping speed of 2000 mm·s-1, friction coefficient of 0.125 and clearance between punch and die of 0.87 mm.

基金项目：

山东省科技发展计划项目（2014GGX103035）

王言德（1989-），男，硕士研究生；Email：1274436573@qq.com；通讯作者：胡心平（1969-），男，博士，教授；Email：huxxpp@qlu.edu.cn

参考文献：

［1］刘治中.板式换热器板片传热与阻力性能及冲圧成形工艺研究
［D］.济南:山东大学，2015.

Liu Z Z. Investigation on Plate Heat Transfer and Resistance Characteristics and Stamping Process Heat Exchangers
［D］. Jinan: Shandong University，2015.

［2］邵拥军，逯凯霄，张文林. 板式换热器的特点与优化设计
［J］.广州化工,2012，40(6):120-122.

Shao Y J, Lu K X, Zhang W L. The characteristics and optimization design of the plate heat exchangers
［J］. Guangzhou Chemical Industry, 2012，40 (6):120-122.

［3］余静飞. 板式换热器优化设计研究
［D］.乌鲁木齐：新疆大学，2013.

Yu J F. The Optimize Design of Plate Heat Exchanger
［D］. Urumchi: Xinjiang University，2013.

［4］陶晓钢. 浅析板式换热器板片在压制中出现的问题
［J］. 广州化工，2015，43(19)：141-143.

Tao X G. Analysis of problems in the corrugated plate pressing process of the plate heat exchanger
［J］. Guangzhou Chemical Industry,2015，43(19):141-143.

［5］李奇涵，刘海静，李笑梅，等. 基于Dynaform的汽车顶盖冲压成形回弹模拟及回弹补偿
［J］.锻压技术,2015，40(10):16-23.

Li Q H, Liu H J, Li X M，et al. Springback simulation and compensation of car roof stamping based on Dynaform
［J］. Forging & Stamping Technology，2015，40(10):16-23.

［6］刘细芬，黄华艳，张洪锐. 基于CAE技术的汽车覆盖件拉延模具设计
［J］.机械设计与制造,2010, (4):242-244.

Liu X F, Huang H Y, Zhang H R. Die design of drawing for the auto-mobile panel based on CAE technology
［J］. Machinery Design & Manu facture, 2010, (4):242-244.

［7］缑彦甫，王冲，张学文. 基于Dynaform的一种新型拉延模结构设计与应用
［J］. 锻压技术，2016，41(12):107-113.

Gou Y F, Wang C, Zhang X Y. Structure design and application for a new drawing die based on Dynaform
［J］.Forging & Stamping Technology, 2016，41(12):107-113.

［8］安家菊.基于Dynaform 宽凸缘拉深件数值模拟分析
［J］.机械设计与制造,2011, (9):193-195.

An J J. Based on the Dynaform for wide flange drawing part of numerical simulation analysis
［J］. Machinery Design & Manufacture, 2011, (9):193-195.

［9］赵磊. 等效拉延筋和真实拉延筋对顶盖后横梁模拟成形质量的影响
［J］.锻造与冲压，2011，(3): 57-62.

Zhao L. Influence of equivalent drawbead and true drawbead on simulation forming quality of the rear cover beam
［J］. Forming & Metalforming, 2011，(3): 57-62.

［10］杨立军，齐艳梅，党新安.基于DYNAFORM的筒形件拉深成形数值模拟技术
［J］.机械设计与制造,2011, (10):228-230.

Yang L J, Qi Y M, Dang X A. Technology of numerical simulation for deep drawing cylindrical parts based on DYNAFORM
［J］. Machinery Design & Manufacture, 2011, (10):228-230.

［11］孟凡芳，徐凯，宋慧，等.基于CAD/CAE的汽车覆盖件拉延模设计
［J］.锻压技术,2017，42(1):98-100.

Meng F F, Xu K, Song H，et al. Design of drawing die for automobile panel based on CAD/CAE
［J］.Forging & Stamping Technology, 2017，42(1): 98-100.

服务与反馈：

【文章下载】【加入收藏】