锻压技术

铸锻复合成形6063铝合金的工艺优化

英文标题：Process optimization of compound casting and forging for aluminum alloy 6063

作者：王丽萍叶霞

分类号：TG146.2

出版年,卷(期):页码：2018,43(8):90-96

摘要：

采用不同的锻压力、启锻时间和保压时间进行了6063铝合金的铸锻复合成形，并进行了室温力学性能和耐磨损性能的测试和分析。结果表明，随锻压力从70 MPa增加到150 MPa、启锻时间从2 s增加到6 s、保压时间从5 s增加到35 s，试样的力学性能和耐磨损性能均先提升后下降。与70 MPa锻压力相比，采用130 MPa锻压力时合金的抗拉强度增大42 MPa、磨损体积减小18×10-3 mm3；与2 s启锻时间相比，采用6 s启锻时间时合金的抗拉强度增大17 MPa，磨损体积减小7×10-3 mm3；与5 s 保压时间相比，采用25 s保压时间时合金的抗拉强度增大29 MPa，磨损体积减小13×10-3 mm3。6063铝合金的铸锻复合成形工艺参数优选为：130 MPa锻压力、4 s启锻时间和25 s保压时间。

The compound casting and forging process of aluminum alloy 6063 with different forging pressures, forging-starting time and holding time was carried out, and the mechanical property and wear resistance property at room temperature were tested and analyzed. The results show that with forging pressure increasing from 70 MPa to 150 MPa, forging-starting time increasing from 2 s to 6 s, and holding time increasing from 5 s to 35 s, the mechanical properties and wear resistance property of samples both increase first, and then decrease. Compared with forging pressure of 70 MPa, the tensile strength of alloy increases up by 42 MPa and the wear volume decreases by 18×10-3 mm3 when the forging pressure is 130 MPa. Compared with forging-starting time of 2 s, the tensile strength of alloy increases by 17 MPa, and the wear volume decreases by 7×10-3 mm3 when the forging-starting time is 6 s. However, compared with holding time of 5 s, the tensile strength increases by 29 MPa and the wear volume decreases by 13×10-3 mm3 when the holding time is 35 s. Finally, the optimal process parameters of the compound casting and forging of aluminum alloy 6063 are chosen as forging pressure of 130 MPa, forging-starting time of 4 s and holding time of 25 s.

基金项目：

等职业教育研究院资助项目（CDGZ2015025）；2018年江苏省高职院校教师专业带头人高端研修（团队访学）项目资助（2018TDFX002）

王丽萍（1973-），女，硕士，副教授 E-mail：dsh3322@163.com

参考文献：

［1］郎利辉，孙志莹，王耀. 板料成形汽车大型铝合金覆盖件的充液成形技术
［J］. 锻压技术，2017，42（8）：22-27.

Lang L H，Sun Z Y，Wang Y. Hydroforming technology for large aluminum alloy panel of automobile
［J］. Forging & Stamping Technology，2017，42（8）：22-27.

［2］徐骏，田战峰，曾怡丹，等.铝合金半固态加工技术的应用研究
［J］.特种铸造及有色合金，2007，27(8):603-607.

Xu J, Tian Z F, Zeng Y D, et al. Application research on semi-solid processing technologies for aluminum alloys
［J］. Special Casting & Nonferrous Alloys, 2007, 27(8): 603-607.

［3］郑晖，赵曦雅.汽车轻量化及铝合金在现代汽车生产中的应用
［J］.锻压技术，2016，41(2):1-5.

Zheng H, Zhao X Y. Lightweight automobile and application of aluminum alloys inmodern automobile production
［J］. Forging & Stamping Technology, 2016, 41(2): 1-5.

［4］徐静，王顺成，郑开宏，等.启锻时间对铸锻复合成形2014铝合金组织与性能的影响
［J］.特种铸造及有色合金，2016，36(12):1253-1257.

Xu J, Wang S C, Zheng K H, et al. Microstructure and mechancial properties of 2014 aluminum alloy prepared by casting-forging integrated technology under varied forging-starting time
［J］. Special Casting & Nonferrous Alloys, 2016, 36(12): 1253-1257.

［5］张磊.铝合金半固态流变铸锻成形技术基础研究
［D］.武汉：华中科技大学，2012.

Zhang L. Study on Technology of the Integration of Rheo-casting and Forging Process for Aluminum Alloy
［D］. Wuhan: Huazhong University of Science and Technology, 2012.

［6］李伟东.A356铝合金铸锻复合成形技术研究
［D］.长沙：中南大学，2013.

Li W D. A Study of the Combination Forming Technology of Die Casting Forging of A356 Aluminum
［D］. Changsha:Central South University, 2013.

［7］彭勇，王顺成，郑开宏，等.铸锻复合一体化成形6061铝合金的组织和力学性能
［J］.中国有色金属学报，2014，(2):325-334.

Peng Y, Wang S C, Zheng K H, et al. Microstructure and mechanical properties of 6061 aluminum alloy prepared by casting-forging integrated technology
［J］. The Chinese Journal of Nonferrous Metals, 2014, (2):325-334.

［8］彭勇，王顺成，郑开宏，等.启锻时间对铸锻复合成形6061合金组织和性能的影响
［J］.特种铸造及有色合金，2013，33(12):1152-1157.

Peng Y, Wang S C, Zheng K H, et al. Microstructure and mechancial properties of 6061 aluminum alloy prepared by casting-forging integrated technology under varied forging-starting time
［J］. Special Casting & Nonferrous Alloys, 2013, 33(12): 1152-1157.

［9］陈萌，陈思悦，裴小虎，等.轿车的后转向节零件铸锻复合成形工艺研究
［J］.特种铸造及有色合金，2012，32(6)：518-521.

Chen M, Chen S Y, Pei X H, et al. Casting and forging compound process for producing steering knuckles of car
［J］. Special Casting & Nonferrous Alloys, 2012, 32(6):518-521.

［10］闫红红，李永堂，胡勇，等. 基于铸辗复合成形工艺的Q235B环形铸坯
［J］. 塑性工程学报，2015，22 (1): 34-38.

Yan H H，Li Y T，Hu Y，et al. Q235B ring casting blank for cast-rolling forming technology
［J］. Journal of Plasticity Engineering, 2015, 22(1):34-38.

［11］张琦，曹苗，张帅，等.汽车轮毂铸锻一体化制造工艺
［J］.塑性工程学报，2014，21(2):1-6.

Zhang Q, Cao M, Zhang S, et al. Integrated casting and forging process for aluminum alloy automobile wheel
［J］. Journal of Plasticity Engineering, 2014, 21(2):1-6.

［12］谭建波，杨帅，李祎超.工艺参数对半固态流变铸—锻6061合金成形性的影响
［J］.河北科技大学学报，2016，37(1):65-69.

Tan J B, Yang S,Li Y C. Effect of technological parameters onformability of semi-solid rheological casting-forging 6061 alloy
［J］. Journal of Hebei University of Science and Technology,2016, 37(1):65-69.

服务与反馈：

【文章下载】【加入收藏】