锻压技术

冲压模具的结构变形分析及型面补偿技术

英文标题：Structural deformation analysis and profile surface compensation technology for a stamping die

作者：石光林程金海夏明祥吕少文周雪兆

单位：广西科技大学

分类号：TG386

出版年,卷(期):页码：2018,43(8):168-172

摘要：

针对某款汽车发动机盖外板，采用钣金冲压仿真软件DYNAFORM对其冲压成形进行模拟仿真，获得模具与板料间的接触力信息；随后通过钣金冲压分析软件JSTAMP，将DYNAFORM中获得的壳体接触力映射到冲压模具实体结构网格上，对模具进行结构变形分析来获得模具型面的变形数据，再根据这些数据来制定和实施其型面补偿方案，得到更加合理的模具型面结构。在生产现场，对未实施型面补偿的模具和实施了型面补偿的模具的调试工作进行对比分析，统计各自的修模量及研合率调试时间。结果表明，使用该方法可达到提高模具研合率，减少修模工作量，实现缩短模具制造周期的目的。

For outer plate of a car engine cover, the stamping process was simulated by sheet metal punching simulation software DYNAFORM，and the contact forces between die and sheet were obtained. Then, the shell contact forces obtained by DYNAFORM were mapped to the structural grid of stamping die by sheet metal punching analysis software JSTAMP, and the structural deformation of die was analyzed to obtain the deformation data of die profile surface. Based on the above data, the compensation scheme of profile surface was designed and conducted, and more reasonable profile surface structure of die was obtained. Furthermore, at manufacturing site, the debugging work of dies with and without profile surface compensation were compared，and the die repair and debugging time of matching rate were measured. The result shows that the above method can improve the matching rate of die, decrease the die repair and also shorten the manufacturing cycle of the stamping die.

基金项目：

广西科技攻关项目（桂科攻1598008-23）

石光林(1967-)，男，硕士，教授，E-mail：shiguanglin@gxust.edu.cn；通讯作者：程金海(1979-)，男，硕士研究生，E-mail：597526079@qq.com

参考文献：

［1］陈志新，黄凡.基于Moldflow和ANSYS的注塑模具变形模拟分析
［J］.机械设计与制造，2009，(3)：246-248.

Chen Z X, Huang F. Injection mold deformation analysis base on Moldflow and ANSYS
［J］. Machinery Design & Manufacture,2009,(3):246-248.

［2］李捷，董洪全，殷玉枫.钣金件模具在冲压过程中的变形分析
［J］.现代制造工程，2006，(8)：56-58.

Li J, Dong H Q, Yin Y F. Deformation analysis of sheet metal die in the process of punching
［J］.Modern Manufacturing Engineering,2006,(8):56-58.

［3］刘源.高强度钢板冲压模具强度分析与结构优化
［D］.长沙：湖南大学，2015.

Liu Y. Strength Analysis and Structure Optimization for High Strength Steel Stamping Die
［D］.Changsha: Hunan University, 2015.

［4］ Mori T, Takatsuji N, Matsuki K， et al.Measurement of pressure distribution on die surface and deformation of extrusion die in hot extrusion of 1050 aluminum rod
［J］.Journal of Materials Processing Technology, 2002,(130-131): 421-425.

［5］ Hur K D, Choi Y, Yeo H T.Design for stiffness reinforcement in backward extrusion die
［J］.Journey of Materials Processing Technology, 2002, (130-131)：411-415.

［6］李东君.基于Dynaform的某汽车外板件拉延分析与模具设计
［J］. 锻压技术，2016，41（4）：151-155.

Li D J. Analysis and die design on outer panel drawing part of automobile based on Dynaform
［J］. Forging & Stamping Technology，2016，41（4）：151-155.

［7］张贵宝.高强度薄板拉深模具结构分析关键研究及应用
［D］.上海：上海交通大学，2008.

Zhang G B. Research and Application on the Key Technologies of High Strength Steel Drawing Die Structure Analysis
［D］. Shanghai:Shanghai Jiao Tong University, 2008.

［8］朱林.装载机板焊驱动桥壳疲劳寿命的研究
［D］.柳州：广西科技大学，2014.

Zhu L. Fatigue Life Study for Welding Drive Axle Housing
［D］. Liuzhou: Guangxi University of Science and Technology, 2014.

［9］岳陆游，陈炜.板料冲压成形有限元模拟分析
［J］.电加工与模具， 2003，(1)：40-44.

Yue L Y, Chen W. Finite element simulation analysis on stamping forming of sheet metal
［J］. Electro Machining and Mould, 2003，(1)：40-44.

［10］邓超.成形力的求解及其在模具结构优化中的应用
［D］.长沙：湖南大学，2011.

Deng C. Calculation of Sheet Metal Forming Force and Its Application on Die Structural Design
［D］.Changsha：Hunan University, 2011.

［11］万晓峰，刘岚.LMS Virtual.Lab Motion入门与提高
［M］.西安：西北工业大学出版社，2010.

Wan X F, Liu L. LMS Virtual.Lab Motion Introduction and Improvement
［M］.Xi′an: Northwestern Polytechnical University Press，2010.

［12］刘细维.基于优化模板的扫掠体六面体网格生成
［D］. 杭州：浙江大学，2015.

Liu X W. Hexahedral Mesh Generation of Swept Volume Based on Optimized Template
［D］. Hangzhou: Zhejiang University，2015

［13］许剑，林滔.基于JSTAMP/NV的冲压模具变形分析
［J］.计算机辅助工程，2016，25（3）：69-73.

Xiu J, Lin T. Analysis on deformation of stamping die based on JSTAMP/NV
［J］. Computer Aided Engineering, 2016, 25(3):69-73.

［14］闫巍，张健，王文瑞，等.汽车覆盖件冲压模具的结构变形分析
［J］.汽车工艺与材料，2013，(1)：68-71.

Yan W, Zhang J, Wang W Y，et al. Structural deformation analysis for punching die stamping car covering parts
［J］. Automotive Technology & Materials, 2013,(1):68-71.

［15］王忠华，张立彪，周晓松.拉延凹模动态模面补偿方法研究
［J］.汽车工艺与材料，2015，(5)：11-13.

Wang Z H, Zhang L B, Zhou X S. Dynamic molded surface compensation solution study on drawing die
［J］. Automotive Technology & Materials, 2015,(5):11-13.

服务与反馈：

【文章下载】【加入收藏】