锻压技术

变薄拉深筒形件尺寸偏差的分析与研究

英文标题：Analysis and research on dimensional deviation of ironing for cylindrical part

作者：许文文梅瑛何镏源

单位：中北大学

分类号：TG376

出版年,卷(期):页码：2019,44(4):90-94

摘要：

在变薄拉深冷成形工艺中，减薄率是对整个筒形件尺寸精度有着重要影响的工艺参数。为了探究减薄率对变薄拉深筒形件尺寸精度的影响，以C15-c低碳钢材料为研究对象，在Simufact.forming有限元仿真软件中，对该研究对象不同减薄率下的变薄拉深冷成形工艺进行数值模拟分析，并把变薄拉深后筒形件的外圆度误差与壁厚偏差作为评价指标，探究变薄拉深冷成形工艺时减薄率对筒形件尺寸精度的影响。结果表明：随着减薄率的增大，筒形件的外圆度误差呈现先减小后增大的趋势；随着减薄率的增大，筒形件的壁厚偏差呈现增大的趋势；实验结果与仿真结果的变化规律一致，两者之间的误差小于10%，说明有限元仿真具有良好的可靠性。

In the process of ironing cold forming, the thinning rate is an important process parameter influencing on the dimensional accuracy of the whole cylindrical part. In order to explore the influence of thinning rate on the dimensional accuracy of ironing for cylindrical part, for the C15-c low carbon steel, the processes of ironing cold forming with different thinning rates were simulated and analyzed by finite element simulation software Simufact.forming, and the influence of thinning rate on the dimensional accuracy of cylindrical part in the ironing cold forming process was investigated by taking the outer roundness error and wall thickness deviation of cylindrical part after ironing as the evaluation indexes. The results show that with the increasing of thinning rate, the outer roundness error of cylindrical part decreases first and then increases, and the wall thickness deviation of cylindrical part increases. The variation rules of experimental result and simulation result are consistent, and the error between them is less than 10%, thus the finite element simulation has good reliability.

基金项目：

国家自然科学基金资助项目（51275486）

许文文（1990-），男，硕士研究生 E-mail：657522059@qq.com 通讯作者：梅瑛（1964-），女，学士，教授 E-mail：2286419285@qq.com

参考文献：

[1]葛丹丹，金峰，樊文欣.筒形件强力旋压有限元数值模拟技术的研究[J].热加工技术，2011，40(11)：93-95,100.

Ge D D, Jin F, Fan W X. Research on numerical simulation technology for cylinders power spinning [J]. Hot Working Technology, 2011, 40 (11): 93-95,100.

[2]崔长齐，林晨华，武美,等.变薄拉深成形过程中毛坯开裂的原因分析与预防[J].精密成形工程, 2013, 5（3）:73-76.

Cui C Q, Lin C H, Wu M, et al. Analysis on the cause of blank breaks produced during ironing and preventive measures [J].Journal of Netshape Forming Engineering, 2013, 5（3）:73-76.

[3]贺全智，李辉，赵利鼎. 基于Simufact的多道次变薄拉深尺寸精度研究[J].锻压技术，2018,43(9):108-112.

He Q Z, Li H, Zhao L D, et al. Research on dimensional accuracy of multi-step ironing based on Simufact [J]. Forging & Stamping Technology，2018, 43(9):108-112.

[4]李辉, 杨峰, 梁忠强. 多道次变薄拉深尺寸精度研究与优化[J]. 塑性工程学报, 2018, 25(6): 41-47.

Li H, Yang F, Liang Z Q. Study and optimization of dimension accuracy of multi-step ironing[J]. Journal of Plasticity Engineering, 2018, 25(6): 41-47.

[5]许江平, 柳玉起, 章志兵, 等. 实体单元在变薄拉深成形模拟及工艺参数优化中的应用[J]. 中国机械工程, 2009, 20(6): 110-113.

Xu J P, Liu Y Q, Zhang Z B, et al. Application of solid element in ironing simulation and optimization of processing parameters [J]. China Mechanical Engineering, 2009, 20(6): 110-113.

[6]周杰，胡建军, 张勇, 等.变薄拉深中回弹分析与实验研究[J].中国机械工程, 2003，14（1）: 20-22.

Zhou J, Hu J J, Zhang Y, et al. Analysis and study on spring in ironing [J]. China Mechanical Engineering,2003，14（1）: 20-22.

[7]邵振江,胡鹏飞, 张建莹, 等. 局部变薄拉深冲压件成形工艺研究[J]. 机械设计, 2018, 35(S1):320-321.

Shao Z J, Hu P F, Zhang J Y, et al. Forming process research on locally thinned drawing stamping parts [J]. Journal of Machine Design, 2018, 35(S1):320-321.

[8]肖善超. 弹壳多模一次连续变薄拉深工艺研究[D]. 秦皇岛: 燕山大学, 2012.

Xiao S C. Research on Multi-mode-one-off Ironing Process for Cartridge Cas[D]. Qinhuangdao: Yanshan University,2012.

[9]平欣, 平鹏. 圆度、同轴度和圆柱度误差的最小二乘评定法[J]. 中国测试, 1997,23(2): 44-46.

Ping X, Ping P. The least square method for evaluating the errors of roundness, axiality and cylindricity[J]. China Measurement & Test,1997,23(2): 44-46.

[10]宋要斌，李辉，赵登峰. 多道次变薄拉深速度对筒形件尺寸精度的影响[J].锻压技术，2018,43(7):165-169.

Song Y B，Li H，Zhao D F. Influence of multi-pass ironing speed on dimension accuracy of cylindrical parts [J]. Forging & Stamping Technology，2018,43(7):165-169.

[11]杨锋，樊文欣，汤传尧，等. 基于Simufact筒形件强力旋压与变薄拉深成形质量研究[J].锻压技术，2018,43(2):49-54.

Yang F，Fan W X，Tang C Y，et al. Quality research on power spinning and ironing for cylindrical part based on Simufact [J]. Forging & Stamping Technology，2018,43(2): 49-54.

[12]李晋, 李辉.多模一次变薄拉深筒形件尺寸精度研究[J].热加工工艺，2018, 47 (11): 117-119.

Li J, Li H. Study on dimensional accuracy of multi-die one-time ironing cylindrical parts [J]. Hot Working Technology, 2018, 47(11): 117-119.

服务与反馈：

【文章下载】【加入收藏】