锻压技术

多工位全工序连续冲压工艺仿真与实验

英文标题：Simulation and experiment of multi-position and complete process continuous stamping process

作者：李钦生徐亮陆勤强梁静

单位：安徽机电职业技术学院

分类号：TG385.2

出版年,卷(期):页码：2019,44(9):40-45

摘要：

以某电子接插件壳体为研究对象，借助CAE技术对薄壁零件进行多工位冲压工艺研究。首先，采用一次拉延成形数值模拟预测零件的成形缺陷，然后确定零件的多工位冲压工序方案和排样图；其次，采用多工位全工序模拟方法，通过采用不同成形工艺参数组合，对零件整个成形过程不断进行仿真优化，最终达到零件图纸所要求的精度和使用性；最后，采用模拟时的最佳工艺参数组合对零件进行冲压试验，检测和分析实际冲制的零件。结果表明：多工位全工序成形模拟结果与实际试验结果基本吻合。因此，多工位全工序数值模拟方法在多工位级进模设计过程中是有效的和可行的，并且缩短了零件的开发和试模周期。

For the shell of an electronic connector, the multi-position stamping process of thin-walled part was studied by CAE technology. First of all, the forming defects of part were predicted by the numerical simulation of one-step drawing, and then the multi-position stamping process plan and layout diagram of part were determined. Then, the multi-position and complete process simulation method was adopted, and through the combination of different forming process parameters, the whole forming process of part was continuously simulated and optimized to achieve the accuracy and usability requirements by part drawing. Finally, the stamping test of part was conducted by the best combination of process parameters in simulation, then the actual stamping part was detected and analyzed. The results show that the simulation results of multi-position and complete process forming are in agreement with the experimental results. Therefore, the numerical simulation method of multi-position and complete process is effective and feasible in the design process of multi-position progressive die, and the cycle of part development and die test are shorten.

基金项目：

安徽高校自然科学研究重点项目（KJ2018A0871，KJ2018A0859)

李钦生(1975-)，男，硕士，讲师 E-mail：ahjdlqs@126.com

参考文献：

［1］徐晓，王二冬，夏琴香，等.某汽车底梁加固件冲压成形全工序数值模拟分析
［J］.现代制造工程，2017，（8）：57-62.

Xu X, Wang E D, Xia Q X, et al. Numerical simulation analysis of complete stamping process for stiffener part of automotive beam
［J］. Modern Manufacturing Engineering, 2017，(8)：57-62.

［2］陈宝全，李国强，顾强，等.汽车轮侧内板冲压工艺仿真与试验
［J］.锻压技术，2017，42（12）：26-29.

Chen B Q, Li G Q, Gu Q, et al.Simulation and experiment of automobile wheel side inner plate in stamping process
［J］. Forging & Stamping Technology,2017,42(12)：26-29.

［3］李钦生，何俊，刘彦春，等.矩形件分块压边圈深拉延成形及拉延模设计
［J］.锻压技术，2018，43（3）：42-45.

Li Q S, He J, Liu Y C, et al. Drawing of rectangular box with segment blank holders and its drawing die design
［J］. Forging & Stamping Technology, 2018,43(3)：42-45.

［4］李钦生，何俊，俞蓓，等.矩形件正反拉延成形工艺研究及变工序模具设计
［J］.锻压技术，2018，43（6）：37-40.

Li Q S, He J, Yu B, et al. Research on forwards-reverse drawing of rectangular parts and variable-process die design
［J］. Forging & Stamping Technology,2018,43(6)：37-40.

［5］周敏，熊禾根，李贵，等.复杂汽车零件多工位级进模全工序数值模拟
［J］.锻压技术，2017，42（12）：31-34.

Zhou M, Xiong H G, Li G, et al.Numerical simulation of whole process for multi-station progressive die of complex automotive structure parts
［J］.Forging & Stamping Technology, 2017,42(12):31-34.

［6］贺全智，李辉，赵利鼎.基于Simufact的多道次变薄拉深尺寸精度研究
［J］.锻压技术，2018，43(9) ：108-112.

He Q Z, Li H, Zhao L D.Research on dimensional accuracy of multi-step ironing based on Simufact
［J］.Forging & Stamping Technology，2018，43(9) ：108-112.

［7］夏琴香，魏光明，叶福源，等.多工位级进冲压全工序数值模拟关键技术研究
［J］.华南理工大学学报：自然科学版，2012，40（7）：63-66.

Xia Q X, Wei G M, Ye F Y, et al. Investigation into key technologies of numerical simulation of whole process chain during multi-position progressive stamping
［J］. Journal of South China University of Technology: Natural Science Edition, 2012, 40(7):63-66.

［8］Deng K, Pan P, Sun J, et al. Shape optimization design of steel shear panel dampers
［J］. Journal of Constructional Steel Research, 2014, 99:187-193.

［9］王二冬.多工位级进冲模模具结构分析及优化关键技术研究
［D］.广州：华南理工大学，2016.

Wang E D.Research on the Technologies of Structure Analysis and Optimization of Multi-position Progressive Die
［D］. Guangzhou: South China University of Technology, 2016.

［10］王明伟，高莹莹，吕艳.高强钢汽车加强板冲压成形数值模拟及试验
［J］.锻压技术，2017，42（2）：61-64.

Wang M W, Gao Y Y, Lyu Yan.Numerical simulation and test of stamping forming for automobile reinforcing plate with high strength steel
［J］. Forging & Stamping Technology,2017,42(2)：61-64.

［11］林忠钦.车身覆盖件冲压成形仿真
［M］.北京：机械工业出版社，2005.

Lin Z Q. Stamping Simulation of Body Covering Parts
［M］.Beijing: China Machine Press,2005.

［12］王树博.基于CAE技术的多工位薄板冲压成形数值模拟工艺研究
［D］.长沙：湖南大学，2016.

Wang S B. A CAE Approach to the Numerical Simulation Technology Formed by Multi-position Sheet Metal Technology
［D］. Changsha:Hunan University,2016.

服务与反馈：

【文章下载】【加入收藏】