锻压技术

基于Autoform的汽车天窗加强环成形模拟及工艺优化

英文标题：Forming simulation and process optimization on automobile skylight reinforcement ring based on Autoform

作者：权宏张海波

单位：东北电力大学

分类号：TG386.1

出版年,卷(期):页码：2020,45(6):53-58

摘要：

以某型号汽车天窗加强环为研究对象，通过对其结构进行分析，初步设计冲压工艺为拉延修边、冲孔修边、冲孔翻边，初选压边力、摩擦系数、拉延筋阻力系数、工艺补充等参数，并利用Autoform进行数值模拟。根据模拟结果中所出现的起皱、减薄、开裂等缺陷，并结合产品结构，调整压边力、摩擦系数以及拉延工艺以得到符合实际生产的工艺参数、冲压工艺。最终确定的工艺参数为：压边力为2400 kN、凸凹模间隙为1.2 mm、摩擦系数为0.15；冲压工艺为：拉延修边、冲孔修边、冲孔翻遍、整形冲孔。根据确定的工艺参数进行成形实验，得到了合格的零件，有效地降低了模具的设计成本。

For the skylight reinforcement ring of a certain model automobile, its stamping process was preliminarily designed as drawingtrimming, punchingtrimming, punchingflanging by analyzing its structure. Then, the parameters, such as blank holder force, friction coefficient, drawbead resistance coefficient and process supplement, were preliminarily selected, and its forming process was numerically simulated by Autoform. According to the wrinkling, thinning, cracking and other defects in the simulation results and the structure of product, the blank holder force, friction coefficient and drawing process were adjusted to obtain the process parameters and stamping process that were in line with the actual production. Finally, the process parameters were determined as follows the blank holder force of 2400 kN, the clearance between punch and die of 1.2 mm and the friction coefficient of 0.15, and the stamping process was designed as drawingtrimming, punchingtrimming, punchingflanging, shapingpunching. According to the determined process parameters, the forming experiment was conducted, and the qualified parts were obtained to reduce the design cost of mold effectively.

基金项目：

权宏（1992-），男，硕士研究生 E-mail：384370625@qq.com 通讯作者：张海波（1970-），男，博士，教授，硕士生导师 E-mail：zhbzhb1970@163.com

参考文献：

［1］熊志, 寻璋.乘用车天窗加强框结构的优化研究
［J］.现代制造技术与装备,2018，(3):20-22.

Xong Z, Xun Z. Optimization research on frame structure of passenger car sunroof
［J］.Modern Manufacturing Technology and Equipment, 2018, (3):20-22.

［2］江财茂. 汽车天窗风振噪声研究与优化
［A］. 中国汽车工程学会汽车空气动力学分会.2018中国汽车工程学会汽车空气动力学分会学术年会论文集
［C］.上海：中国汽车工程学会汽车空气动力学分会:中国汽车工程研究院股份有限公司汽车风洞中心(筹),2018.

Jiang C M. Research and optimization of sunroof buffeting noise
［A］.Automatic Aerodynamic Committee of China SAE.Paper Collection of Automatic Aerodynamic Committee of China SAE in 2018
［C］. Shanghai：Automatic Aerodynamic Committee of China SAE: Automobile Wind Tunnel Center of China Automobile Engineering Research Institute Co., Ltd.,2018.

［3］姜旭, 周六如.基于Autoform汽车左中侧围内板加强板成形模拟及工艺优化
［J］.锻压技术,2018,43(10):47-51.

Jiang X, Zhou L R. Forming simulation and process optimization on automobile left middle side inner panel reinforcement plate based on Autoform
［J］. Forging & Stamping Technology, 2018,43(10):47-51.

［4］徐肖, 黄涛,王震.基于CAE的典型前围板下横梁冲压成形工艺
［J］.锻压技术,2019,44(8):26-35.

Xu X, Huang T, Wang Z. Stamping process of typical front beam connecting part based on CAE
［J］. Forging & Stamping Technolo-gy, 2019,44(8):26-35.

［5］陈俊安. 汽车尾灯安装加强件拉延成形工艺参数优化
［J］.锻压技术,2019,44(11):56-63.

Cheng J A. Optimization on drawing process parameters of an automobile taillight installation reinforcement
［J］. Forging & Stamping Technology,2019,44(11):56-63.

［6］杨西荣, 井菲菲,刘晓燕,等.模具角度对CP-Zr室温ECAP变形组织与性能的影响
［J］.稀有金属,2018,42(4):367-372.

Yang X R, Jing F F, Liu X Y, et al. Microstructure and properties of CP-Zr by ECAP at room temperature with different die angles
［J］. Chinese Journal of Rare Metals,2018,42(4):367-372.

［7］尹振入, 卢立伟,盛坤，等.有限元分析锥台转角对镁合金板材成形性的影响
［J］.稀有金属,2018,42(5):470-476.

Ying Z R, Lu L W, Sheng K, et al. Finite element analysis of magnesium sheet formability with different frustum angles
［J］. Chinese Journal of Rare Metals,2018,42(5):470-476.

［8］陆建军, 赵威,陈炜,等.汽车地板加强板拉延成形工艺
［J］.锻压技术,2018,43(11):38-41.

Lu J J, Zhao W, Cheng W, et al. Drawing forming process of floor reinforcing plate for automobile
［J］. Forging & Stamping Technology, 2018,43(11):38-41.

［9］肖瑞, 杨明,黄朝文.基于响应面法对211ZX新型高强铝合金固溶工艺的优化设计
［J］.稀有金属,2019,43(10):1040-1046.

Xiao R, Yang M, Huang C W. Optimal design of 211ZX high strength aluminum alloy solid solution process based on response surface method
［J］. Chinese Journal of Rare Metals,2019,43(10):1040-1046.

［10］李欣, 孙延朋,王丹,等.汽车前地板成形有限元数值模拟
［J］.吉林大学学报：工学版,2019,49（5）:1608-1614.

Li X, Sun Y P, Wang D, et al. Finite element numerical simulation for automobile front floor forming
［J］. Journal of Jilin University：Engineering and Technology Edition,2019,49（5）:1608-1614.

［11］鲜敏, 彭威,于培师,等.T形盒形件拉延冲压工艺优化
［J］.锻压技术,2019,44(12):20-26.

Xian M, Peng W, Yu P S, et al. Optimization on drawing and stamping process for T-shaped box
［J］. Forging & Stamping Technology,2019,44(12):20-26.

［12］左治江, 张宇辉,丁元才.基于AutoForm的汽车顶盖拉延工艺分析及模具设计
［J］.锻压技术,2019,44(3):101-106.

Zuo Z J, Zhang Y H, Ding Y C. Drawing process analysis and die design of automobile roof cover based on AutoForm
［J］. Forging & Stamping Technology,2019,44(3):101-106.

服务与反馈：

【文章下载】【加入收藏】