锻压技术

5A02铝合金管端旋转冲压双扩口成形过程精确预测

英文标题：Precise prediction of double flaring forming process of 5A02 aluminum alloy tube end by rotating-stamping

作者：彭江涛1 2 李宏伟1 2 詹梅1 2 李一岩1 王巧玲3 曹金豆3 李光俊3 荣建3

单位：1.西北工业大学材料学院凝固技术国家重点实验室 2. 陕西省高性能精确成形技术与装备重点实验室 3. 航空工业成都飞机工业（集团）有限公司

分类号：TG386

出版年,卷(期):页码：2021,46(9):112-117

摘要：

针对双扩口管端头难以夹持成形的问题，采用了双扩口管端旋转冲压成形工艺，降低了双扩口管端头的成形力。建立了旋转冲压双扩口成形与回弹全过程的有限元模型，实现了管端双扩口成形的精确预测。结果表明：相比于冲压双扩口，旋转冲压双扩口成形可显著降低夹持凹模所需要提供的夹持力（从18 kN降低至1 kN），低至前者的10%以下；管端头扩口颈部不贴模现象主要发生在单扩道次，且不明显；内翻道次成形后，管端的变形状态对双扩口管的最终成形质量有着显著的影响。当采用2.0 mm≤圆角半径r≤3.0 mm、85°≤半锥角φ≤90°的旋轮进行内翻时，可成形出效果较好的双扩口管端。

For the problem that it is difficult to clamp and form the end of double flaring tube, the rotating-stamping process of double flaring for tube end was used to reduce the forming force of double flaring for tube end. The finite element model of

the whole process consisted of double flaring forming by rotating-stamping and springback was established, which achieved accurate prediction of the double flaring forming for tube end. The results show that the clamping force required by holding the die can be reduced significantly to less than 10% (from 18 kN to 1 kN) for double flaring forming by rotating-stamping compared with double flaring forming by stamping. The phenomenon of the badly fittability in the neck of flaring is not obvious, which mainly occurs in the single flaring pass. The deformation state of the tube end after the inversion pass forming has a significant influence on the quality of the double flaring tube. Using the spinning roller of 2.0 mm≤ radius of rounded corners r≤3.0 mm and 85°≤half of cone angle φ≤90° to turn inward, a double flaring tube end of better quality can be formed.

基金项目：

彭江涛（1996-），男，硕士研究生 E-mail：pengjiangtao212@163.com 通信作者：李宏伟（1978-），男，博士，教授 E-mail：lihongwei@nwpu.edu.cn

参考文献：

[1]章涛. 5A02铝合金导管冲压双扩口成形机理及变形规律研究 [D]. 西安: 西北工业大学，2017.

Zhang T. Study on Forming Mechanism and Deformation Law of Double Flaring in Aluminum Alloy Pipe Stamping [D]. Xi′an: Northwestern Polytechnical University, 2017.

[2]钟翔山, 吴国栋. 底盘油管成形工艺及模具设计 [J]. 模具制造，2012，12(11)：56-58.

Zhong X S, Wu G D. Forming process and die design of chassis tubing [J]. Die ＆ Mould Manufacture, 2012，(11): 56 -58.

[3]王巧玲，詹梅，李宏伟，等. 大直径薄壁管双扩口成形机理与工艺研究 [J]. 塑性工程学报，2019，26（3）：104-112.

Wang Q L, Zhan M, Li H W, et al. Research on forming mechanism and process of double flaring tubes with large diameter and thin wall [J]. Journal of Plasticity Engineering, 2019, 26(3); 104-112.

[4]牛卫中. 薄壁圆管件锥面型冲压扩口的应力与壁厚分析 [J]. 华中科技大学学报: 自然科学版，2004,32(4)：13-15，37.

Niu W Z. Analysis of the stress and wall-thickness on stamping-expanding of connoid thin-walled cylindrical-tube workpiece [J].Journal of Huazhong University of Science ＆ Technology: Nature Science Edition, 2004, 32 (4):13-15，37.

[5]褚亮，卢险峰，张建，等. 管材锥形凹模缩口成形力数学模型研究 [J]. 矿山机械，2008，36(22)：100-104.

Chu L, Lu X F, Zhang J, et al. Study on the mathematical model of deformation pressure for tube necking with conical die [J].Mining ＆ Processing Equipment, 2008, 36 (22): 100-104.

[6]Kitazawa. Criteria for outward curling of tubes [J]. Journal of Manufacturing Science & Engineering, 1993, 115(4):466-471.

[7]Huang Y M. Influence of punch radius and angle on the outward curling process of tubes [J]. International Journal of Advanced Manufacturing Technology, 2002, 19(8):587-596.

[8]Almeida B P P, Alves M L, Rosa P A R, et al. Expansion and reduction of thin-walled tubes using a die: Experimental and theoretical investigation [J]. International Journal of Machine Tools & Manufacture, 2006, 46(12):1643-1652.

[9]Alves M L, Martins P A F. Forming of thin-walled tubes into toroidal shells[J]. Journal of Materials Processing Technology, 2009, 210(4): 689-695.

[10]El-Domiaty A. Curling of thin tubes: Analytical and experimental study [J]. Journal of Materials Engineering and Performance, 1997, 6(4):481-495.

服务与反馈：

【文章下载】【加入收藏】