锻压技术

基于汽车差速器齿轮热锻二次成形齿顶面折叠缺陷的成形数字仿真及工艺研究

英文标题：Forming digital simulation and process research based on tooth top surface folding defect in hot forging secondary forming for automobile differential gear

作者：李林鑫1 崔志亮2 赖丽莉1 冯铃1

单位：1.四川化工职业技术学院智能制造学院 2.四川众友机械有限责任公司

关键词：汽车差速器齿轮热锻二次成形折叠缺陷毛坯温度数字仿真

分类号：

出版年,卷(期):页码：2022,47(3):23-27

摘要：

针对汽车差速器齿轮热锻二次成形中出现的齿顶面折叠缺陷，利用UG和Deform-3D软件进行了有限元三维建模和仿真模拟，发现了缺陷产生的原因。在此基础上，首先，通过调整毛坯尺寸获得了较为理想的成形效果。然后，研究了摩擦因数对成形质量的影响，确定摩擦因数为0.3时会再次出现折叠缺陷。再以毛坯温度和锻压速度为变量，研究了两者对成形质量的影响，得到最大成形载荷随着毛坯温度和锻压速度的增加而减小，并且当金属变形抗力低于一定程度时会再次出现缺陷。最后，确定了最佳的工艺参数，并通过真实生产得到了无缺陷的产品，验证了最佳工艺参数的正确性，提高了生产效率。

For the folding defect of tooth top surface in the hot forging secondary forming of automobile differential gear, the finite element three-dimensional modeling and simulation were carried out by software UG and Deform-3D, and the cause of the defect was found. On this basis, by adjusting the blank size, an ideal forming effect was obtained. Then the influence of friction factor on the forming quality was investigated, and it was concluded that the defect appeared again when the friction factor was 0.3. Furthermore, taking the blank temperature and forging speed as variables, the influences of the two on the forming quality were investigated, it was obtained that the maximum forming load decreased with the increase of blank temperature and forging speed, and the defects appeared again when the metal deformation resistance was lower than a certain degree. Finally, the optimal process parameters were determined. At last, through the real production, the products without defects were obtained, which verified the correctness of the optimized process parameters and improved the production efficiency.

基金项目：

四川省教育厅课题 ( 17ZB0277)

作者简介：李林鑫（1984-），男，硕士，副教授 E-mail：179207987@qq.com

参考文献：

[1]赵伟平, 刘江涛,贾倩.基于Deform的齿轮泵从动齿轮轴闭式模锻数值模拟分析[J].热加工工艺,2020,49(13):93-95，99.

Zhao W P,Liu J T,Jia Q. Numerical simulation and analysis of closed die forging of gear pump follower gear shaft based on Deform[J].Hot Working Technology，2020,49(13):93-95，99.

[2]蒋磊, 龚剑,王龙,等.侧围外板浅拉延成形工艺数值模拟[J].塑性工程学报, 2020,27(9):73-81.

Jiang L,Gong J,Wang L,et al. Numerical simulation of shallow drawing for body side outer panel[J]. Journal of Plasticity Engineering,2020,27(9):73-81.

[3]陈云, 倪俊芳,花维维, 等.基于DEFORM-3D直齿锥齿轮锻造模具的精确设计[J].煤矿机械,2019,40(2):86-88.

Chen Y, Ni J F, Hua W W, et al．Accurate design of forging die for straight bevel gears based on DEFORM-3D[J]. Coal Mine Machinery,2019,40(2):86-88.

[4]赵利民, 任云晖.基于UG和ANSYS的齿轮模具设计及有限元仿真[J].煤矿机械,2019,40(12):180-182

Zhao L M, Ren Y H. Design and finite element simulation of gear mold based on UG and ANSYS[J]. Coal Mine Machinery, 2019,40(12):180-182

[5]何伟, 董万鹏,孙礼宾，等.基于Deform-3D的发动机齿轮轴热锻成形结构优化模拟[J].塑性工程学报,2019,26(6):42-49.

He W,Dong W P,Sun L B,et al． Structural optimization simulation of engine gear shaft hot forging based on Deform-3D[J].Journal of Plasticity Engineering，2019，26(6):42-49.

[6]周梦娟, 冯玮.圆柱螺旋齿轮热精锻过程齿变形规律的研究[J].热加工工艺,2020,49(7):84-88.

Zhou M J,Feng W. Study on tooth deformation law of cylindrical helical gear during hot precision forging[J]. Hot Working Technology,2020,49(7):84-88.

[7]陈金霞, 吕文春,赵春来.基于Deform的螺旋伞齿轮轴楔横轧工艺的数值模拟[J].热加工工艺,2020,49(1):96-98.

Chen J X,Lyu W C,Zhao C L. Numerical simulation of cross wedge rolling process for spiral bevel gear shaft based on Deform[J].Hot Working Technology，2020,49(1)：96-98.

[8]曹国英. 工艺参数对汽车变速器驱动齿轮轴温锻质量的影响[J].热加工工艺,2019,48(21):109-111，115.

Cao G Y. Effect of process parameters on warm forging quality of driving gear shaft of automotive transmission[J]. Hot Working Technology, 2019,48(21):109-111，115.

[9]夏玉峰，杨建兵，田永生，等．基于响应面法的汽车离合器盘毂温锻-冷精整工艺多目标优化[J]. 中南大学学报: 自然科学版，2015,46(9):3203-3210.

Xia Y F，Yang J B，Tian Y S，et al． Multi-object optimization of warm forging-cold sizing technology for automobile clutch disc-hub based on response surface model [J]. Journal of Central South University: Science and Technology,2015,46(9):3203-3210.

[10]高畅, 金俊松,王新云,等.弧齿锥齿轮开式冷精锻工艺优化设计[J].模具工业,2020,46(12):40-45.

Gao C, Jin J S, Wang X Y,et al. Process optimization of closed cold precision forging of spiral bevel gear[J]. Die & Mould Industry,2020,46(12):40-45.

[11]董奇, 金飞翔,秦强,等.基于正交试验齿圈座热锻成形工艺优化[J].塑性工程学报,2021,28(8):18-22.

Dong Q,Jin F X,Qin Q，et al．Optimization of hot forging forming process based on orthogonal test for gear ring seat[J].Journal of Plasticity Engineering,2021,28(8):18-22.

[12]段海龙. 42CrMo结合齿热锻成形机理及微观组织演变规律研究[D].唐山：华北理工大学,2021.

Duan H L. Study on the Mechanism and Microstructure Evolution of 42CrMo Conjunction Gear During Forging Process[D]. Tangshan:North China University of Science and Technology,2021.

服务与反馈：

【文章下载】【加入收藏】