锻压技术

三通阀体多向模锻工艺研究及有限元分析

英文标题：Research on wear failure for pre-forging die of piston

作者：王耀1 顾小燕2

分类号：

出版年,卷(期):页码：2022,47(3):28-33

摘要：

针对40Cr合金钢阀体生产效率低、材料利用率低、性能差、寿命短等问题，提出了采用多向模锻工艺来成形阀体。首先，根据阀体结构特征设计了3种成形工艺方案，并分析了各方案冲头的加载方式；其次，通过CAE分析软件Deform-3D完成了各方案的有限元建模，并进行了数值仿真，分析比较了各方案的锻件成形过程、锻件成形质量、锻件温度分布、成形载荷等。结果表明：采用方案3的锻件成形过程更为合理，温度分布更为均匀，载荷较小，锻件质量更好。最后，以方案3为参考，进行了多向模锻工艺试验，获得了质量较好的阀体锻件。经检验，与仿真结果的一致性较高，表明有限元技术可对实际模锻工艺提供一定的理论指导，提高设计效率。

For the problems of low production efficiency, low material utilization, poor performance and short service life of 40Cr alloy steel valve body, a multi-directional die forging process was proposed to form the valve body. Firstly, three forming process schemes were designed according to the structural characteristics of the valve body, and the loading modes of punch for each scheme were analyzed. Secondly, the finite element model of each scheme was completed by CAE analysis software Deform-3D, and the numerical simulation was carried out. Furthermore, the forging process, forging quality, forging temperature distribution and forming load of each scheme were analyzed and compared. The results show that the forging process of scheme 3 is more reasonable, the temperature distribution is more uniform, the load is smaller， and the forging quality is better. Finally, taking scheme 3 as a reference, the multi-directional die forging process test was carried out, and the valve body forgings with good quality were obtained. After inspection, the consistency with the simulation results is high, which shows that the finite element technology can provide some theoretical guidance for the actual die forging process and improve the design efficiency.

基金项目：

江苏省自然科学基金资助项目（BK20140509）

作者简介：王耀（1984-），男，硕士，讲师 E-mail：wangyao841025@163.com

参考文献：

[1]刘东帅. 冲头速率对多向模锻液压阀体质量的影响[J].热加工工艺,2020,49(9):92-94，102.

Liu D S. Effect of punch rate on quality of hydraulic valve body formed by multi-direction die forging[J]. Hot Working Technology,2020,49(9):92-94，102.

[2]任运来, 李明权,任杰,等.高温高压阀体的多向模锻技术研究[J].重型机械,2015，(5):1-5.

Ren Y L, Li M Q, Ren J, et al. Study on multi-ram forging technology of high temperature high pressure valve body[J]. Heavy Machinery,2015，(5):1-5.

[3]刘光辉, 刘华,王涛,等.仪表阀体多向可控精密成形工艺[J].锻压技术,2020,45(3):8-13.

Liu G H, Liu H, Wang T, et al. Multi-directional controllable precision forming for instrument valve body[J]. Forging & Stamping Technology,2020,45(3):8-13.

[4]郑彬彬, 董传勇,薛克敏,等.三通阀体多向模锻工艺研究[J].精密成形工程,2010,2(5):61-63.

Zheng B B, Dong C Y, Xue K M, et al. Study on multi-ram forging process of triple-valve body[J]. Journal of Netshape Forming Engineering,2010,2(5):61-63.

[5]胡洋. 汽车转向节多向模锻精密成形数值模拟研究[D]. 重庆：重庆理工大学,2013.

Hu Y. Multi-directional Forging Forming Steering Knuckle Which is Studied by Simulation[D]. Chongqing:Chongqing University of Technology,2013.

[6]张卫卫. 模具加载方式对齿轮轴温锻成形性能的影响分析[J].煤矿机械,2019,40(1):138-140.

Zhang W W. Analysis of influence of mold loading method on warm forging performance of gear shaft[J].Coal Mine Machinery,2019,40(1):138-140.

[7]刘航, 李伟,张镜斌.7075铝合金三通阀多向加载成形过程模拟[J].热加工工艺,2021，50(9):101-104.

Liu H,Li W,Zhang J B. Simulation of multi-directional loading forming process of 7075 aluminum alloy tee valve[J].Hot Working Technology,2021，50(9):101-104.

[8]顾文俊, 李俊杰,赵坤民.空排止回阀阀体多向模锻工艺分析[J].热加工工艺,2020,49(11):81-85.

Gu W J,Li J J,Zhao K M. Analysis of multi-directional die forging process for valve body of air vent check valve[J].Hot Working Technology,2020,49(11):81-85.

[9]胡建军. DEFORM-3D塑性成形CAE应用教程[M]. 北京：北京大学出版社, 2011.

Hu J J. DEFORM-3D Plastic Forming CAE Application Course[M]. Peking：Peking University Press, 2011.

[10]张东民, 盛育东,张金玉,等.六角开槽螺母的冷镦工艺优化及数值模拟[J].机械设计与制造,2018，(3):191-194.

Zhang D M, Sheng Y D, Zhang J Y, et al. Numerical simulation and optimization for cold heading of hexagonal slot nut[J]. Machinery Design ＆ Manufacture,2018，(3):191-194.

[11]马世登, 奚建清.基于Deform的齿轮支架锻造成形仿真分析[J].热加工工艺,2017,46(7):148-149，152.

Ma S D,Xi J Q. Simulation analysis for forging forming of gear bracket based on Deform[J].Hot Working Technology,2017,46(7):148-149，152.

[12]孙国柱. 基于有限元法的三通管接头多向模锻成形仿真与优化[J].锻压技术,2021，46(2):28-33.

Sun G Z. Simulation and optimization of multi-direction die forging for tee pipe joint based on finite element method[J]. Forging & Stamping Technology,2021，46(2):28-33.

服务与反馈：

【文章下载】【加入收藏】