锻压技术

航空座椅连接件多工位级进模设计

英文标题：Design on multi-station progressive die for aero seat connector

作者：王巍李珍张贺吴黎艳

单位：沈阳航空航天大学

分类号：TG386

出版年,卷(期):页码：2022,47(10):223-228

摘要：

根据航空座椅连接件的形状、尺寸、材料以及生产要求，对其进行冲压工艺分析。设计了由4个冲裁工位、4个弯曲工位、2个翻边工位、1个压型工位、1个切断工位和2个空工位构成的排样方案。该排样采用单侧载体，步距为50 mm，材料利用率为45.1%，提出采用多工位级进模进行生产。由于该工件的结构中弯曲成形较多，回弹不易控制，对其材料的回弹角进行了仿真，在弯曲成形中考虑了回弹量并进行模具补偿。为了便于维修和拆卸，采用直通式异形凸模，采用悬挂式销钉固定；圆孔冲裁凸模采用阶梯台肩固定，凹模均采用镶块式结构；并采用定位销进行定位，保证了模具精度。经过试模生产，多工位级进模的结构设计合理，能够满足零件的精度要求。

Based on the shape, size, material and production requirements of aero seat connector, its stamping process was analyzed, and a layout scheme consisting of four blanking stations, four bending stations, two flanging stations, one pressing station, one cutting station and two empty stations was designed, which adopted a single-sided carrier, the step distance was 50 mm and the material utilization rate was 45.1%. A multi-station progressive die was proposed to produce. Because there were many parts in the structure of workpiece need bending, it was difficult to control the springback. Therefore, the springback angle of the material was simulated, the springback amount was considered in the bending, and the die compensation was conducted. Furthermore, in order to facilitate maintenance and disassembly, the straight through special-shaped punch was used and fixed by suspended pins. Then the blanking punches with round holes were fixed by the stepped shoulder structures, the dies adopted the insert block structure, and the positioning pins were used to ensure the accuracy of the die. The production results show that the structure of multi-station progressive die is reasonable, which can meet the accuracy requirements of the part.

基金项目：

航空科学基金资助项目（2020Z006054002）

王巍（1978-），女，博士，副教授，E-mail：wangwei7832@163.com

参考文献：

[1]郑伟，李赫亮，袁晓光，等. 汽车用AlMgSi系合金板材的研究现状及发展趋势[A]. 中国机械工程学会铸造分会. 2010年中国铸造活动周论文集[C]. 中国机械工程学会铸造分会，2010.

Zheng W, Li H L, Yuan X G, et al. Auto plate AlMgSi alloy with the present research situation and development trend[A]. Foundry Branch of China Society of Mechanical Engineering. Papers of China Foundry Weekly 2010[C]. Foundry Branch of China Society of Mechanical Engineering, 2010.

[2]金龙建，陈炎嗣. 多工位级进模排样工艺分析[J]. 模具制造，2012，12(10)：44-50.

Jin L J, Chen Y S. Analysis of layout process for the multi-position progressive die[J]. Die & Mould Manufacture, 2012, 12(10):44-50.

[3]陈泽中，刘欢，谢洪昊，等. 22MnMoB钢汽车后地板横梁热冲压成形数值模拟和工艺研究[J].塑性工程学报，2020,27（2）：13-20.

Chen Z Z, Liu H, Xie H H, et al. Numerical simulation and process analysis of 22MnMoB steel in hot stamping for automobile rear floor crossmember[J].Journal of Plasticity Engineering，2020,27（2）：13-20.

[4]范鹏飞，杨俊杰. 旋转卡扣多工位级进模设计[J]. 模具制造，2017，17(11)：28-33.

Fan P F, Yang J J. Design of multistation progressive die for the rotary buckle[J]. Die & Mould Manufacture, 2017, 17(11):28-33.

[5]佟玉斌，葛紫红. 多次弯曲弹性元件多工位级进模设计[J]. 热加工工艺，2011，40(13)：175-177.

Tong Y B, Ge Z H. Design of multiposition progressive die for multistep bending elastic element[J]. Hot Working Technology 2011, 40(13):175-177.

[6]曹秒艳，田少杰，胡晗，等. 超声振动辅助铝合金板冲裁研究[J].塑性工程学报，2020, 27（3）：1-9.

Cao M Y，Tian S J，Hu H，et al. Research on ultrasonic vibration assisted blanking of aluminum alloy sheet [J].Journal of Plasticity Engineering，2020, 27（3）：1-9.

[7]徐涛涛，孔垂品，李俊杰，等.汽车覆盖件冲压工艺分析系统[J].塑性工程学报，2020,27（5)：74-82.

Xu T T, Kong C P, Li J J，et al. Process analysis system for stamping of automobile panel[J]. Journal of Plasticity Engineering，2020,27（5)：74-82.

[8]袁博，陈淑花，张耀，等. 压簧折弯多工位级进模具设计[J]. 锻压技术，2021，46(5)：190-193.

Yuan B, Chen S H, Zhang Y, et al. Design on multi-station progressive die for pressure spring bending[J]. Forging & Stamping Technology, 2021, 46(5):190-193.

[9]闫华军，王峰，刘玉忠，等. 书夹件多工位级进模设计[J]. 热加工工艺，2014，43(11)：120-122.

Yan H J, Wang F, Liu Y Z, et al. Design of multi-station progressive die for bookend parts[J]. Hot Working Technology, 2014, 43(11):120-122.

[10]胡冶昌，魏志芳，李晓光，等. 基于NX高级仿真的弹壳冲盂工序数字化模型研究[J]. 塑性工程报，2017，24(2)：122-127.

Hu Y C, Wei Z F, Li X G, et al. Digital model study on the cartridge case extrusion forming based on NX advanced simulation[J]. Journal of Plasticity Engineering, 2017, 24(2): 122-127.

[11]王巍，张贺，崔旭，等. 卡爪多工位级进模设计[J]. 锻压技术，2020，45(10)：137-141.

Wang W, Zhang H, Cui X, et al. Design of multi-progressive die for claw[J]. Forging & Stamping Technology, 2020, 45(10):137-141.

[12]李云涛,尹博,孙文强,等.激光功率对Cr12MoV钢激光淬火强化的影响[J].模具工业,2013,39(4):73-76.

Li Y T, Yi B, Sun W Q, et al. Effects of laser power on laser quenching of Cr12MoV steel [J]. Die & Mould Industry, 2013,39(4):73-76.

[13]谭丁森，张建勋，秦庆华.带环形焊缝双金属复合管屈曲失效研究[J].塑性工程学报，2021,28（2）：154-161.

Tan D S，Zhang J X，Qin Q H. Research on buckling failure of bimaterial metal pipes with girth weld [J].Journal of Plasticity Engineering，2021,28（2）：154-161.

服务与反馈：

【文章下载】【加入收藏】