锻压技术

平板集磁器对板料小区域电磁成形的影响规律

英文标题：Influence law of plate magnetic collector on electromagnetic forming in small area of sheet metal

作者：黄　春章争荣李　晋张　军陈超军

单位：广东工业大学

分类号：TG391

出版年,卷(期):页码：2023,48(1):72-78

摘要：

利用装配有集磁器的平板电磁成形系统, 研究了金属板料小区域的电磁成形过程以及集磁器对板料电磁力的分布影响规律。结果表明: 通过集磁器的磁场聚集作用, 板料能够完成小区域的变形, 且成形效果较好, 能够贴紧凸模; 板料的变形主要分为3 个阶段, 首先是板料中心区域受到电磁力而发生微小变形, 随着电磁力的增大以及板料获得一定成形速度后, 中心区域快速完成变形, 最后是受力区域向板料外端移动, 在惯性共同作用下发生整体的下移, 完成变形。集磁器能够将板料受力区域集中在中心半径约15 mm 的区域内, 板料的成形高度为4 mm。

The electromagnetic forming process of sheet metal in small area and the influence law of magnetic collector on the distribution of electromagnetic force for sheet metal were studied by using the plate electromagnetic forming system with magnetic collector. The results show that the sheet metal can complete the deformation of small area through the magnetic field aggregation of magnetic collector, the forming effect is good, and the sheet metal can cling to the punch. The deformation of sheet metal is mainly divided into three stages. First, the central area of sheet metal undergoes minor deformation due to electromagnetic force. Then, with the increasing of electromagnetic force and a certain forming speed obtained by the sheet metal, the central area rapidly completes deformation. Finally, the force-bearing area moves to the outer end of sheet metal, and under the joint action of inertia, the overall downward movement occurs to complete the deformation. The magnetic collector can concentrate the force-bearing area of sheet metal in an area with a central radius of about 15 mm, and the forming height of sheet metal is 4 mm.

基金项目：

国家自然科学基金面上项目(500210081)

作者简介: 黄　春(1997-), 男, 硕士 E-mail: 2111902053@ mail2. gdut. edu. cn 通信作者: 章争荣(1969-), 男, 博士, 教授 E-mail: zzr@ gdut. edu. com

参考文献：

[1] 　熊奇, 唐红涛, 王沐雪, 等. 2011 年以来电磁成形研究进展[J]. 高电压技术, 2019, 45 (4): 1171-1181.

Xiong Q, Tang H T, Wang M X, et al. Research progress of electromagnetic forming technique since 2011 [J]. High Voltage Engineering,2019, 45 (4): 1171-1181.

[2] 　Lee M G, Lee S H, Kim S, et al. Electromagnetic forming process analysis based on coupled simulations of electromagnetic analysis and structural analysis [ J]. Journal of Magnetics, 2016, 21(2): 215-221.

[3] 　Cui X H, Mo J H, Zhu Y. 3D modeling and deformation analysis for electromagnetic sheet forming process [ J]. Transactions of Nonferrous Metals Society of China, 2012, 22 (1): 164-169.

[4] 　Cui X H, Mo J H, Li J J, et al. Electromagnetic incremental forming (EMIF): A novel aluminum alloy sheet and tube forming technology [J]. Journal of Materials Processing Tech. , 2014, 214(2): 409-427.

[5] 　Cui X H, Li J, Mo J, et al. Investigation of large sheet deformation process in electromagnetic incremental forming [J]. Materials & Design, 2015, 76 (1): 86-96.

[6] 　Xiong Q, Cao Q, Han X, et al. Axially movable electromagnetic forming system for large-scale metallic sheet [J]. IEEE Transactions on Applied Superconductivity, 2016, 26 (4): 1-4.

[7] 　张敏. 板材电磁成形的试验研究[D]. 北京: 中国机械科学研究院集团有限公司, 2005.

Zhang M. Experiment Research on EMF of Sheet Metal [D]. Beijing: China Academy of Machinery Science and Technology Group, 2005.

[8] 　莫健华, 王波, 崔晓辉, 等. 板料电磁成形集磁器工作原理的模拟[J]. 塑性工程学报, 2011, 18 (1): 36-42.

Mo J H, Wang B, Cui X H, et al. Simulation on the principle of field shaper in electromagnetic sheet metal forming [J]. Journal of Plasticity Engineering, 2011, 18 (1): 36-42.

[9] 　Kumar R, Kore S D. Experimental studies on the effect of different field shaper geometries on magnetic pulse crimping in cylindrical configuration [J]. The International Journal of Advanced Manufacturing Technology, 2019, 105 (6): 4677-4690.

[10] Rajak A K, Kumar R, Kore S D. Designing of field shaper for the electro-magnetic crimping process [J]. Journal of Mechanical Science and Technology, 2019, 33 (11): 5407-5413.

[11] 徐佳辉, 黄亮, 李建军, 等. 基于集磁器的电磁冲裁工艺的设计与模拟[J]. 中国机械工程, 2020, 31 (11): 1368-1377.

Xu J H, Huang L, Li J J, et al. Design and simulation of electromagnetic blanking processes based on field shaper [ J]. China Mechanical Engineering, 2020, 31 (11): 1368-1377.

[12] Zhang H, Liu N, Li X, et al. A novel field shaper with slow-varying central hole for electromagnetic pulse welding of sheet metal [J]. The International Journal of Advanced Manufacturing Technology, 2020, 108 (7-8): 2595-2606.

[13] Yu H P, Li C F, Deng J H. Sequential coupling simulation for electromagnetic mechanical tube compression by finite element analysis [ J]. Journal of Engineering Materials and Technology, 2009, 209 (1): 707-713.

[14] Lee S H, Lee D N. A finite element analysis of electromagnetic forming for tube expansion [J]. Journal of Engineering Materials and Technology, 1994, 116 (2): 250-254.

[15] Li Z, Li C F. Simulation of electromagnetic tube bulging based on loose coupling method [J]. Chinese Journal of Mechanical Engineering, 2006, 19 (4): 566-569.

服务与反馈：

【文章下载】【加入收藏】