锻压技术

42CrMo钢超声滚挤压表面硬度有限元分析及参数优化

英文标题：Finite element analysis and parameter optimization on surface hardness of ultrasonic rolling for 42CrMo steel

分类号：TG376.1

出版年,卷(期):页码：2023,48(3):152-158

摘要：

为了提高42CrMo钢零件的耐腐蚀性和抗疲劳性，基于ABAQUS建立了超声滚挤压有限元仿真模型，通过单因素试验和响应曲面法，分析了工艺参数对42CrMo钢表面硬度的作用规律和影响程度，同时对所建立的二阶响应曲面模型进行了显著性检验和工艺参数优化。结果表明，42CrMo钢的表面硬度随转速和进给速度的提高呈现先增加后下降的趋势，随着振幅和静压力的增大而增大。由响应曲面分析可知，振幅对表面硬度的影响最大，优化得到最优工艺参数组合为：转速为418 r·min-1、进给速度为15 mm·min-1、振幅为25 μm、静压力为600 N。对优化结果进行超声滚挤压试验，将仿真优化结果和试验结果进行对比，误差在5%以内，验证了超声滚挤压仿真模拟对42CrMo钢的表面硬度进行预测的可行性。

To improve the corrosion resistance and fatigue resistance of 42CrMo steel parts, a finite element simulation model of ultrasonic rolling was established based on ABAQUS, and through single factor test and response surface method, the effect rules and influence degrees of process parameters on the surface hardness of 42CrMo steel were analyzed. At the same time, the significance test and process parameters optimization of the established second-order response surface model were carried out. The results show that the surface hardness of 42CrMo steel increases first and then decreases with the increasing of rotational speed and feeding speed, and increases with the increasing of amplitude and static pressure. From the response surface analysis, it can be seen that the amplitude has the greatest impact on the surface hardness, and the optimal process parameters combination obtained by optimization is the rotation speed of 418 r·min-1, the feeding speed of 15 mm·min-1,the amplitude of 25 μm were and the static pressure of 600 N. The ultrasonic rolling test was carried out on the optimization results, and the simulation optimization results were compared with the test results, and the error is within 5%, which verifies the feasibility of the ultrasonic rolling simulation to predict the surface hardness of 42CrMo steel.

基金项目：

国家自然科学基金资助项目(U1804145)；国家重点研究计划（2018YFB2000405）

作者简介：王排岗(1994-)，男，硕士 E-mail：1395055213@qq.com 通信作者：王晓强（1972-），男，博士，教授 E-mail：wang_xq2002@163.com42CrMo

参考文献：

[1]唱佳林, 李安海. 42CrMo钢多工步车削加工表面完整性研究[J]. 工具技术, 2021,55(7): 49-53.

Chang J L, Li A H. Research on the surface integrity of 42CrMo steel multi-step turning machining [J]. Tool Engineering, 2021, 55(7): 49-53.

[2]于浩, 赵军, 盖少磊, 等. 42CrMo钢车削表面完整性研究[J]. 组合机床与自动化加工技术, 2021,(7): 137-140.

Yu H, Zhao J, Gai S L, et al. Research on surface integrity of 42CrMo steel turning [J]. Modular Machine Tool & Automatic Manufacturing Technique, 2021,(7): 137-140.

[3]张飞, 赵运才. 超声表面滚压改善45#钢表层特性及疲劳性能的研究[J]. 表面技术, 2017, 46(9): 185-190.

Zhang F, Zhao Y C. Study on the improvement of surface properties and fatigue properties of 45# steel by ultrasonic surface rolling [J]. Surface Technology, 2017, 46(9): 185-190.

[4]Bozdana Ali Tolga, Gindy Nabil N Z, Li H． Deep cold rolling with ultrasonic vibrations-A new mechanical surface enhancement technique[J]. International Journal of Machine Tools & Manufacture, 2010, 45(6): 713-718.

[5]Liu Y, Zhao X, Wang D. Determination of the plastic properties of materials treated by ultrasonic surface rolling process through instrumented in dentation[J]. Materials Science and Engineering: A, 2014, 600(32): 21-31.

[6]Li F Q, Zhao B, Lan S L, et al. Experiment and simulation of the effect of ultrasonic rolling on the surface properties of Ti-6Al-4V[J]. The International Journal of Advanced Manufacturing Technology, 2020, 106(5): 1893-1900.

[7]刘治华, 张天增, 杨孟俭, 等. 超声滚压18CrNiMo7-6齿轮钢表面变质层性能分析[J]. 郑州大学学报: 工学版, 2020,41(2): 44-49.

Liu Z H, Zhang T Z, Yang M J, et al. Performance analysis of surface modified layer of ultrasonic rolled 18CrNiMo7-6 gear steel [J]. Journal of Zhengzhou University: Engineering Science, 2020,41 (2): 44-49.

[8]武民, 马利杰, 王占奎, 等. 工艺参数对钛合金超声振动铣削表面显微硬度的影响[J]. 机械科学与技术, 2020, 39(10): 1587-1592.

Wu M, Ma L J, Wang Z K, et al. Influence of process parameters on the surface microhardness of titanium alloy by ultrasonic vibration milling [J]. Mechanical Science and Technology for Aerospace Engineering, 2020, 39(10): 1587-1592.

[9]Shinya Kanou, Masaaki Nishikawa, Hitoshi Soyama. Analysis of the formation of plastic deformation layer on the surface of polycrystalline metals subjected to a micro-size high-rate shot impact[J]. International Journal of Mechanical Sciences,2013,75(3): 316-323.

[10]王晓强, 徐少可, 崔凤奎, 等. 轴承套圈表面超声滚挤压加工硬化模型[J]. 塑性工程学报, 2019, 26(3): 231-237.

Wang X Q, Xu S K, Cui F K, et al. Ultrasonic rolling extrusion work hardening model of bearing ring surface [J]. Journal of Plasticity Engineering, 2019, 26(3): 231-237.

[11]韩璐, 康仁科, 张园, 等. GH4169超声辅助磨削表面完整性研究[J]. 金刚石与磨料磨具工程, 2021, 41(5): 46-51.

Han L, Kang R K, Zhang Y, et al. Research on the surface integrity of GH4169 ultrasonic-assisted grinding [J]. Diamond & Abrasives Engineering, 2021, 41(5): 46-51.

[12]Lu X, Jia Z, Yang K, et al. Analytical model of work hardening and simulation of the distribution of hardening in micro-milled nickel-based superalloy[J]. International Journal of Advanced Manufacturing Technology, 2018, 97: 1-9.

[13]卢也森, 朱志武, 谢奇峻. 基于改进J-C模型的42CrMo钢动态本构关系研究[J]. 四川理工学院学报: 自然科学版, 2016, 29(3): 61-65.

Lu Y S, Zhu Z W, Xie Q J. Research on dynamic constitutive relation of 42CrMo steel based on improved J-C model [J]. Journal of Sichuan University of Science & Engineering: Natural Science Edition, 2016, 29(3): 61-65.

[14]汤井田, 公劲喆. 基于GiD的有限元前处理和后处理可视化[J]. 地球物理学进展, 2010, 25(1): 186-195.

Tang J T, Gong J Z. Visualization of finite element preprocessing and postprocessing based on GiD [J]. Progress in Geophysics, 2010, 25(1): 186-195.

[15]姚国林. 风电轴承材料超声滚挤压表层物理力学性能研究[D]. 洛阳: 河南科技大学，2020.

Yao G L. Research on the Physical and Mechanical Properties of the Surface Layer of Wind Power Bearing Materials by Ultrasonic Rolling [D]. Luoyang: Henan University of Science and Technology, 2020.

[16]刘惠, 刘腾飞, 陈宗强, 等. 基于试验设计和响应曲面法的大型带筋薄壁铝型材挤压工艺优化[J]. 锻压技术, 2022, 47(5):144-152.

Liu H，Liu T F，Chen Z Q，et al. Optimization on extrusion process for large reinforced thin-walled aluminum profile based on experimental design and response surface method[J]. Forging & Stamping Technology, 2022, 47(5):144-152.

[17]李志山, 史耀耀, 辛红敏, 等. 灰色关联度优化钛合金盘铣开槽工艺参数[J]. 西北工业大学学报, 2018, 36(1): 139-148.

Li Z S, Shi Y Y, Xin H M, et al. Optimization of slotting process parameters for titanium alloy disc milling by grey correlation degree [J]. Journal of Northwestern Polytechnical University, 2018, 36(1): 139-148.

服务与反馈：

【文章下载】【加入收藏】