锻压技术

汽车尾门内外板合模工艺研究与应用

英文标题：Research and application on process of forming two parts in one die for automobile tailgate inner & outer panels

作者：何宁曹彪马春华

分类号：TG386.3

出版年,卷(期):页码：2023,48(6):76-83

摘要：

根据汽车尾门内外板的零件尺寸及结构特点，分析了尾门内外板零件的冲压方向、零件工艺性和各工序设计重点内容，并采用Autoform软件进行了有限元仿真，确定了合模工艺的可行性。通过对比尾门内外板合模的优点及问题，分析了合模工艺的优势。针对合模模具调试过程中遇到的OP40模具开模困难问题，提出了平衡尾门内外板侧氮气弹簧压力的改善措施。结果表明：汽车尾门内外板合模工艺能有效降低模具成本、提高生产效率、节约车间运行成本和减少模具存放占地空间，且实物成形良好，无起皱、缩颈开裂等明显的质量缺陷，满足量产装车要求。

According to the dimension and structural characteristics of automobile tailgate inner & outer panels, the stamping direction, technological analysis of parts and design key content of each step were researched. And the finite element simulation analysis was carried out by using Autoform software, the feasibility of forming two parts in one die process was determined. Then, the advantages of forming two parts in one die process were analyzed by comparing the advantages and problems of forming two parts in one die for tailgate inner & outer panels. Furthermore, in view of the difficulty in opening die of OP40 encountered during the debugging of die, the improvement measure to balance the pressure of nitrogen spring in the side of tailgate inner & outer panels was proposed. The result shows that forming two parts in one die process for automobile tailgate inner & outer panels can effectively reduce the die cost, improve production efficiency, save workshop operating cost and reduce the die storage space. Thus, the formed parts are good without obvious quality defects such as wrinkling and cracking etc., which meet the requirements of mass production.

基金项目：

柳州市科学研究与技术开发计划课题（2020GAAD0601）

何宁（1989-），男，硕士，工程师

参考文献：

［1］郑金桥，黄勇，王义林，等.汽车覆盖件冲压工艺设计现状及发展趋势
［J］.塑性工程学报，2003，10(6)：9-14.

Zheng J Q, Huang Y, Wang Y L, et al. Present situation and prospects of stamping process planning for automobile panels
［J］. Journal of Plasticity Engineering, 2003, 10(6): 9-14.

［2］宋桂军.一模多件技术的优缺点及难点解决
［J］.锻造与冲压，2019，(10)：39-42.

Song G J. The advantages, disadvantages and difficulties solving of means for the multi parts in one die
［J］. Forging & Metalforming, 2019, (10): 39-42.

［3］周铁军，王冀军，段彦宾，等.侧围外板废料利用及一模多件技术的相关研究
［J］.模具制造，2018，18(10)：10-14.

Zhou T J, Wang J J, Duan Y B, et al. Research on the means for the more product in one die under the side inner panel scrap
［J］. Die & Mould Manufacture, 2018, 18(10): 10-14.

［4］丁斌，张振，潘家俊，等.基于Dynaform盖板成形工艺研究
［J］.锻造与冲压，2021，519(22)：51-53.

Ding B, Zhang Z, Pan J J, et al. Research on forming process of cover plate based on Dynaform
［J］. Forging & Metalforming, 2021, 519(22): 51-53.

［5］李文明，谷晓玉.汽车后背门内板起皱解决措施
［J］.模具工业，2013，39(10)：52-54.

Li W M, Gu X Y. Solutions to wrinkling of automobile back door inner panel
［J］. Die & Mould Industry, 2013, 39(10): 52-54.

［6］陈东辉，张建.基于CAE的车身覆盖件开裂问题处理及改善措施
［J］.模具工业，2018，44(5)：26-29.

Chen D H, Zhang J. Treatment and optimization of the cracking for automobile cover panel based on CAE analysis
［J］. Die & Mould Industry, 2018, 44(5): 26-29.

［7］赵锋，苏传义，赵超，等.一模多件冲压滑移线控制研究
［J］.模具工业，2020，46(10)：11-16.

Zhao F, Su C Y, Zhao C, et al. Research on controlling slip line in multi-parts stamping process
［J］. Die & Mould Industry, 2020, 46(10): 11-16.

［8］崔军营，陈峰. 后背门外板尾灯口凹坑问题的改进措施
［J］.模具制造，2017，17(8)：27-30.

Cui J Y, Chen F. Improvement measures of the pit problem for the tail hole in the rear panel of the back door
［J］. Die & Mould Manufacture, 2017, 17(8): 27-30.

［9］徐冰锋，罗勇，杨欢.基于AutoForm尾门外板拉深开裂问题的解决方法
［J］.模具工业，2019，45(11)：15-20.

Xu B F, Luo Y, Yang H. Solution on drawing cracking issue of automobile rear door outer panel based on AutoForm
［J］. Die & Mould Industry, 2019, 45(11): 15-20.

［10］刘玉山，赵明，郑飞，等. 后背门内板密封面起皱问题的改善
［J］.模具制造，2020，20(1)：24-28.

Liu Y S, Zhao M, Zheng F, et al. Improvement of wrinkling problem of sealing surface for the back door inner plate
［J］. Die & Mould Manufacture, 2020, 20(1): 24-28.

［11］宋灏.汽车背门内板冲压成形与回弹的数值模拟研究
［D］.天津：天津理工大学，2015.

Song H. Numerical Simulation on Forming and Springback Compensation of the Automobile Backdoor Inner Plate
［D］. Tianjin: Tianjin University of Technology, 2015.

［12］孙刚，隋洲，毕丽娟，等.基于AutoForm的汽车顶盖冲压回弹补偿研究
［J］.模具工业，2021，47(4)：11-15.

Sun G, Sui Z, Bi L J, et al. Research on springback compensation of car roof panel stamping based on AutoForm
［J］. Die & Mould Industry, 2021, 47(4): 11-15.

［13］韩龙帅，王刚，郑学斌，等. 基于Autoform的门内板冲压仿真分析
［J］.塑性工程学报，2021，28(4)：82-88.

Han L S, Wang G, Zheng X B, et al. Simulation analysis of door inner panel stamping based on Autoform
［J］. Journal of Plasticity Engineering, 2021, 28(4): 82-88.

服务与反馈：

【文章下载】【加入收藏】