锻压技术

6014-T4P铝合金组织及织构研究

英文标题：Study on microstructure and texture for 6014-T4P aluminum alloy

分类号：TG146.2

出版年,卷(期):页码：2023,48(7):130-137

摘要：

采用金相显微镜、X射线衍射仪、扫描电镜及电子背散射衍射等实验手段分析6014T4P铝合金在工业试制过程中的组织及织构演变情况。结果表明，3卷热轧试制料中S织构的体积分数较Brass织构和Copper织构多，同时还包含再结晶织构，其R织构的体积分数最多。固溶处理后，试制板材中均存在完全再结晶晶粒，且晶粒分布较为不均匀，特别是B和C卷试制料。A、B和C卷试制料的平均晶粒尺寸分别为31.25、37.16和31.25 μm。粗轧道次（11和13道次）对晶粒尺寸影响不大。A卷T4P态试制料的Cube织构明显小于B和C卷试制料，且其S织构和 Cube织构的体积分数比为1.65∶1，A卷T4P态试制料的包边性能更好，但罗平纹更严重。同时，A、B和C卷T4P态试制料中2°~5°小角度晶界占比分别为35.0%、17.9%和24.0%。

The microstructure and texture evolution of 6014-T4P aluminum alloy in the industrial trial production process were analyzed by experimental analysis means such as metallographic microscope, X-ray diffractometer, scanning electron microscope and electron backscattering diffraction. The results show that the volume fraction of S texture in the three coils of hot-rolled trial material is more than that of Brass texture and Copper texture, and it also contains recrystallization texture with most volume fraction of R texture. After solution treatment, there are completely recrystallized grains in the trial-produced plates, and the grain distribution is relatively uneven, especially for the trial materials of B and C coils. The average grain sizes of the trial materials of A,B,C coils are 31.25, 37.16 and 31.25 μm, respectively. The rough rolling passes (11 and 13 passes) have little effect on the grain size. The Cube texture of the T4P state trial material of coil A is obviously smaller than that of trial materials of B and C coils, and the volume fraction ratio of S texture and Cube texture is 1.65∶1. The hemming performance of T4P state trial material of coil A is better, but the roping is more serious. At the same time, the proportions of 2°-5° small angle grain boundaries in the T4P state trial materials of A,B and C coils are 35.0%, 17.9% and 24.0%, respectively.

基金项目：

基于铝基的交通轻量化科技示范工程(2021SFGC1001)

作者简介：迟蕊（1992-），女，硕士，中级工程师 E-mail：chirui@nanshan.com.cn

参考文献：

[1]范贞贞. AA6014 铝合金退火再结晶机制及成形性能研究 [D]. 重庆：重庆大学，2018.

Fan Z Z. Study on Recrystallization Mechanism During Annealing and Formability of AA6014 Aluminum Alloy [D]. Chongqing：Chongqing University，2018.

[2]苏剑，张辉，滕杰，等. 冷轧前热处理对6016T4P铝合金组织和力学性能的影响 [J]. 材料导报，2017，31(1)：87-91.

Su J，Zhang H，Teng J，et al. Effect of heat treatments before cold rolling on microstructure and mechanical properties of 6016T4P aluminum alloy sheet [J]. Materials Reports，2017，31(1)：87-91.

[3]黄元春，颜徐宇，肖政兵，等. AA6061 铝合金冷轧过程中织构的演变与断裂机制 [J]. 粉末冶金材料科学与工程，2015，20(6)：822-828.

Huang Y C，Yan X Y，Xiao Z B，et al. Texture evolution and fracture mechanism of cold rolled AA6061 alloy [J]. Materials Science and Engineering of Powder Metallurgy，2015，20(6)：822-828.

[4]朱上，李志辉，闫丽珍，等. 预时效对汽车用新型AlMgSiCuZn合金烘烤硬化性的影响 [J]. 稀有金属，2022，46(3)：281-288.

Zhu S，Li Z H，Yan L Z，et al. Bakehardening response in a novel AlMgSiCuZn alloy with preaging [J]. Chinese Journal of Rare Metals，2022，46(3)：281-288.

[5]刘川.汽车铝合金覆盖件原始板材组织性能分析与自然时效对其弯曲性能的影响研究 [D]. 重庆：重庆大学，2015.

Liu C. The Microstructures and Mechanical Properties of Automotive Aluminum Sheets and the Effects of Natural Aging on Their Bendability [D].Chongqing：Chongqing University，2015.

[6]马鸣图，毕祥玉，游江海，等.铝合金汽车板性能及其应用的研究进展 [J]. 机械工程材料，2010，34(6)：1-5.

Ma M T，Bi X Y，You J H，et al. Research progress of property and its application of aluminium alloy auto sheet [J]. Materials for Mechanical Engineering，2010，34(6)：1-5.

[7]付锦. 汽车板用新型铝合金微合金化组织与性能的研究 [D]. 济南：山东大学，2017.

Fu J. Study of Microstructure and Properties on New Microalloyed Aluminum Alloy Used for Automotive Sheet [D]. Ji′nan：Shandong University，2017.

[8]邓运来，王冯权，欧世声，等. 不同温度中间退火对6016铝合金板材组织、织构和力学性能的影响 [J]. 热加工工艺，2019，48(8)：168-172.

Deng Y L，Wang F Q，Ou S S，et al. Effects of intermediate annealing at different temperatures on microstructure and mechanical properties of 6016 aluminum alloy [J]. Hot Working Technology，2019，48(8)：168-172.

[9]夏柳，徐春，白清领，等. 退火后终轧压下量对铝合金轧板织构和深冲性能的影响 [J]. 上海金属，2019，41(2)：29-34.

Xia L，Xu C，Bai Q L，et al. Effect of finishing rolling reduction on texture and deep drawability of rolled aluminum alloy sheet after annealing [J]. Shanghai Metals，2019，41(2)：29-34.

[10]谢锦岳. 6016铝合金板材的织构和微观组织研究 [D]. 重庆：重庆大学，2015.

Xie J Y. Study of Texture and Microstructure of 6016 Aluminum Alloy Sheet [D]. Chongqing：Chongqing University，2015.

[11]Waqas Muhammad，Usman Ali，Abhijit P Brahme，et al. Experimental analyses and numerical modeling of texture evolution and the development of surface roughness during bending of an extruded aluminum alloy using a multiscale modeling framework [J]. International Journal of Plasticity，2019，117：93-121.

[12]林丹.6111铝合金板材织构的研究 [D]. 锦州：辽宁工业大学，2006.

Lin D. Study on Texture of 6111 Aluminum Alloy Sheet [D]. Jinzhou: Liaoning University of Technology，2006.

[13]Samajdar I, Verlinden B, Rabet L, et al. Recrystallization texture in a cold rolled commercial purity aluminum: On the plausible macro and micromechanisms [J]. Materials Science and Engineering: A，1999，266(1)：146-154.

[14]段晓鸽，江海涛，米振莉，等. 轧制方式对6016铝合金薄板组织和塑性各向异性的影响 [J]. 材料工程，2020，48(8)：134-141.

Duan X G，Jiang H T，Mi Z L，et al. Effect of rolling mode on microstructure and plastic anisotropy of 6016 aluminum alloy sheet [J]. Journal of Materials Engineering，2020，48(8)：134-141.

[15]Zhao Z, Mao W, Roters F, et al. A texture optimization study for minimum earing in aluminium by use of a texture component crystal plasticity finite element method [J]. Acta Materialia，2004，52(4)：1003-1012.

[16]袁思雨. 横向轧制对 6016 铝合金组织演变及力学性能的影响 [D]. 湘潭：湖南科技大学，2017.

Yuan S Y. Effect of Cross Rolling on Microstructures Evolution and Mechanical Properties for 6016 Aluminum Alloy [D]. Xiangtan：Hunan University of Science and Technology，2017.

[17]Jin H， Lloyd D J. Roping in 6111 aluminum alloys with various iron contents [J]. Materials Science and Engineering A，2005，403：112-119.

[18]卢成健，蒋丽婷，王玉玲，等. 晶体相场法模拟小角度晶界的位错结构及其演化 [J]. 广西科学，2013，(4)：316-320.

Lu C J，Jiang L T，Wang Y L，et al. Simulating structure of dislocation and its evolution in low angle grain boundary by phase field crystal method [J]. Guangxi Sciences，2013，(4)：316-320.

服务与反馈：

【文章下载】【加入收藏】