锻压技术

工艺方案对高强平板冲压件回弹及补偿的影响

英文标题：Influence of process scheme on springback and compensation for high strength flat stamping part

作者：孔敏1 胡伟 2

分类号：TG386

出版年,卷(期):页码：2023,48(10):75-80

摘要：

为解决高强度平板冲压件回弹问题严重以及模拟过程中回弹和回弹补偿不稳定等问题，以某汽车电池盒盖板为研究对象，通过对该零件的全工序回弹进行分析，探究了导致其回弹补偿不稳定的因素及影响规律，对比分析了5种工艺方案并确定了控制该零件回弹的最优方案。冲压实验验证表明：对于高强度平板冲压件，若采用落料成形方案，通过工艺优化的方法无法控制其回弹，且回弹不稳定，工艺稍有改动便会造成回弹趋势的改变；但采用拉延-修边冲孔-翻边翻孔的拉延成形方案，回弹稳定且合格。本研究方法及研究思路对类似零件的生产具有指导意义。

In order to solve the serious springback problem of high-strength flat stamping parts and the instability of springback and springback compensation during the simulation process, for a certain automotive battery box cover plate, through the full process springback analysis of the part, the factors that affected the instability of springback compensation and their influencing laws were explored, and after comparative analysis of five process plans, the optimal plan for controlling the springback of part was determined. Then,the stamping experiments verification shows that for high-strength flat stamping parts, if a blanking forming scheme is used, the springback cannot be controlled through the process optimization methods, and the springback is unstable. A slight change in the process causes a change in the springback trend. However, a drawing forming solution of drawing drawing-trimming and punching-flanging is adopted, the springback is stable and qualified. The research method and research ideas have guiding significance for the production of similar parts.

基金项目：

湖北省教育厅科学技术研究计划项目（B2021334）

孔敏（1991-），女，硕士，讲师 E-mail：13207131768@163.com

参考文献：

［1］杨玉贵,丁哲,胡建全.汽车覆盖件顶盖冲压工艺方案标准化研究
［J］.模具制造,2021,21(7):8-12.

Yang Y G, Ding Z, Hu J Q.Research on standardization of top cover stamping process plan for automobile panels
［J］. Die & Mould Manufacture,2021,21 (7): 8-12.

［2］叶梦彬.浅拉延技术在汽车覆盖件冲压工艺上的应用
［J］.锻造与冲压,2023,(16):50-54.

Ye M B. Application of shallow drawing technology in automotive panel stamping process
［J］. Forging & Metalforming, 2023,(16): 50-54

［3］梁发周,钟圣滔.基于AutoForm模拟的汽车B柱加强板热冲压工艺分析与优化设计
［J］.锻压技术,2022,47(12):75-80.

Liang F Z, Zhong S T. Analysis and optimization design of hot stamping process for automotive Bpillar reinforcement plate based on AutoForm simulation
［J］. Forging & Stamping Technology, 2022,47 (12): 75-80.

［4］Sumikawa S, Ishiwatari A, Hiramoto J, et al. Improvement of springback prediction accuracy using material model considering elastoplastic anisotropy and bauschinger effect
［J］. Journal of Materials Processing Technology,2016, 230(645):1-7.

［5］谢晖, 沈云飞, 王杭燕. 基于改进响应面模型的冲压回弹工艺稳健性优化
［J］. 塑性工程学报, 2018, 25 (4): 26-32.

Xie H, Shen Y F, Wang H Y. Robustness optimization of stamping springback based on improved response surface model
［J］. Journal of Plasticity Engineering, 2018, 25(4):26-32.

［6］孙刚,隋洲,毕丽娟,等.基于AutoForm的汽车顶盖冲压回弹补偿研究
［J］.模具工业,2021,47(4):11-15.

Sun G, Sui Z, Bi L J, et al. Research on springback compensation of car roof panel stamping based on AutoForm
［J］. Die & Mould Industry,2021,47(4):11-15.

［7］Wu Z J,Gong J J,Chen Y D, et al. Springback prediction of dieless forming of AZM120 sheet metal based on constitutive model
［J］.Metals,2020, 10(6):124-131.

［8］Jin L, Yang Y F,Li R Z, et al. Study on springback straightening after bending of the Usection of TC4 material under hightemperature conditions
［J］.Materials,2020,13(8):88-95.

［9］朱超. 汽车前门外板冲压成形工艺优化设计及回弹补偿
［D］. 镇江:江苏大学,2018.

Zhu C.Optimization Design and Springback Compensation of the Stamping Forming Process of the Automobile Front Door Outer Panel
［D］. Zhenjiang:Jiangsu University, 2018.

［10］Wang Z, Hu Q, Yan J, et al. Springback prediction and compensation for the third generation of UHSS stamping based on a new kinematic hardening model and inertia relief approach
［J］. The International Journal of Advanced Manufacturing Technology, 2017, 90(1-4): 875-885.

［11］Wu J,Zhang Z.An improved procedure for manufacture of 3D tubes with springback concerned in flexible bending process
［J］.Chinese Journal of Aeronautics,2021,34(11):267-276.

［12］闫浩涵,林春雷,许晓燕.背门内板涂胶支撑爪冲压工艺补偿方案
［J］.模具工业,2020,46(10):16-18,26.

Yan H H, Lin C L, Xu X Y. Compensation scheme for stamping process of glued supporting claw in tail gate inner panel
［J］. Die & Mould Industry, 2020, 46 (10): 16-18,26.

［13］唐妍,蒋松.翼子板内板冲压工艺数值模拟及回弹补偿
［J］.锻压技术,2021,46(12):105-111.

Tang Y, Jiang S. Numerical simulation and springback compensation on stamping process for fender inner plate
［J］. Forging ＆ Stamping Technology, 2021,46 (12): 105-111.

［14］涂小文.基于AutoForm 软件的回弹计算及补偿技术揭秘(上册)
［M］.武汉:湖北科学技术出版社,2016.

Tu X W.Rebound Calculation and Compensation Technology Revelation Based on AutoForm Software:Volume1
［M］.Wuhan:Hubei Science and Technology Publishing House Press, 2016.

服务与反馈：

【文章下载】【加入收藏】