锻压技术

非薄壁长管类零件校直量计算建模和仿真验证

英文标题：Modeling and simulation verification on straightening amount calculation for non-thin-walled long pipe parts

作者：刘阔张超朱俊澄李凯王永青

分类号：G941

出版年,卷(期):页码：2023,48(10):81-87

摘要：

针对目前国内长管类零件校直量严重依赖人工经验且校直精度低、效率低的问题，开展了长管类零件校直量计算模型研究。基于弹塑性变形理论，通过探究校直过程中长管类零件的变形规律，明确校直力与变形挠度的关系，进而推导并建立了校直量计算模型，可通过此模型计算一定初始变形下校直管件所需的校直量。使用Matlab实现了模型的编程计算，并基于ANSYS软件进行了长管类零件校直过程的模拟仿真，验证了模型的计算精度。验证结果表明：模型计算结果与仿真分析结果的相对误差小于10%，精度较高，可作为校直量制定的重要参考。

For the current problem that the straightening amount of long pipe parts in China relied heavily on manual experience and had low straightening accuracy and low efficiency, the calculation model of the straightening amount of long pipe parts was studied. Then, based on the elasto-plastic deformation theory, the relationship between the straightening force and the deformation deflection of long pipe parts was clarified by exploring the deformation law of long pipe parts in the process of straightening, and the calculation model of straightening amount was derived and established, which could calculat the required straightening amount of pipe parts under certain initial deformation. Furthermore, the programming calculation for the model was realized by Matlab, and the simulation of the straightening process of the long pipe parts was carried out based on software ANSYS, which verified the calculation accuracy of the model. The verification results show that the relative error between the model calculation results and the simulation analysis results is less than 10%, and the accuracy is high, which can be used as an important reference for formulating the straightening amount.

基金项目：

辽宁省科技重大专项（2020JH1/10100016）；辽宁省‘兴辽英才计划’项目（XLYC1807081）

刘阔（1983-），男，博士，教授 E-mail： liukuo0727@qq.com

参考文献：

［1］Natarajan A, Peddieson J. Simulation of beam plastic forming with variable bending moments
［J］. International Journal of NonLinear Mechanics, 2011, 46(1):14-22.

［2］王立权, 廖洪千, 李怀亮, 等. 卷管铺设中管道校直模型及理论研究
［J］. 哈尔滨工程大学学报, 2016, 37(5):718-723.

Wang L Q, Liao H Q, Li H L, et al. Research on straightening model and theory of pipe in coiled pipe laying
［J］. Journal of Harbin Engineering University, 2016, 37(5): 718-723.

［3］周磊, 余忠华. 基于弹塑性理论的T型导轨校直模型研究
［J］. 浙江大学学报：工学版, 2010,44(2):368-372.

Zhou L, Yu Z H. Study on Tguide alignment model based on elasticplastic theory
［J］. Journal of Zhejiang University: Engineering Science Edition, 2010,44(2):368-372.

［4］Zang Y, Lu H, Zhang Y Q, et al. A straightness control system for motor shaft straightening with the stroke prediction algorithm
［A］.6th International Conference on Systems and Informatics
［C］.Shanghai: Institute of Electrical and Electronics Engineers Inc.,2019.

［5］崔甫. 校直理论与参数计算
［M］.北京:机械工业出版社,1994.

Cui F. Straightening Theory and Parameter Calculation
［M］. Beijing: China Machine Press,1994.

［6］Lu H, Ling H,Leopold J. Improvement on straightness of metal bar based on straightening strokedeflection model
［J］. Science in China Series E: Technological Sciences, 2009,52 (7):1866-1873.

［7］Zhao J, Song X K, Cao H Q, et al. Press straightening control strategy of multistep threepoint bending for LSAW pipes
［J］. Journal of Harbin Institute of Technology, 2014, 46(1):90-96.

［8］Galvis J C, Maury H E, Hernandez R J. Elastoplastic model to determine the maximum force for shaft straightening process
［J］. Ingeniería e Investigación, 2017,37(2):107-110.

［9］Kai W, Wang B Y, Yang C C. Research on the multistep straightening for the elevator guide rail
［J］. Procedia Engineering, 2011, 16:459-466.

［10］宋晓抗,赵军.大型直缝焊管压力矫直载荷修正系数优化
［J］.哈尔滨工业大学学报,2014,46(11):90-94.

Song X K, Zhao J. Optimization of correction coefficient for pressure straightening load of large straight seam welded pipe
［J］. Journal of Harbin Institute of Technology,2014,46(11):90-94.

［11］Zhang Y G, Lu H, Zhang X B, et al. A novel analytical model for straightening process of rectanglesection metal bars considering asymmetrical hardening features
［J］. Advances in Mechanical Engineering, 2018,10(9).

［12］Mao H J, Li Z, Lan J, et al. Threepoint bending straightening algorithm and verification for Itype seamless welded rail
［J］. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2022, 236(9):1181-1198.

［13］邢伟荣,孔德文,张红伟. 平行辊矫直对板材残余应力的影响
［J］. 锻压技术,2021,46(12):100-104.

Xing W R，Kong D W，Zhang H W. Effect of parallel roll straightening on residual stress of sheet
［J］. Forging & Stamping Technology，2021,46(12):100-104.

［14］周娣. 长管类零件校直数值模拟技术研究
［D］. 重庆：重庆理工大学，2020.

Zhou D. Research on Numerical Simulation Technology for Alignment of Long Tube Parts
［D］. Chongqing：Chongqing University of Technology，2020.

［15］陈家栋. 基于机器学习的长管类零件校直系统研究
［D］. 重庆:重庆理工大学, 2020.

Chen J D. Research on Straightening System of Long Tube Parts Based on Machine Learning
［D］. Chongqing:Chongqing University of Technology, 2020.

［16］韩宾, 王肖笛, 滕朝斌,等. 薄壁细长轴自适应校直技术
［J］. 锻压技术, 2022,47(2):100-105.

Han B，Wang X D，Teng C B，et al. Selfadaptive straightening technology of thinwalled slender shaft
［J］. Forging & Stamping Technology,2022,47(2):100-105.

服务与反馈：

【文章下载】【加入收藏】