网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
基于伺服压力机的波纹板冲压成形工艺与回弹研究
英文标题:Research on stamping process and springback for corrugated plate based on servo press
作者:刘健1 2 丁明明2 沈铖2 3 张晨阳2 3 林健1 2 
单位:1.宁夏大学 机械工程学院  2.浙江水利水电学院 机械与汽车工程学院 3.华北水利水电大学 机械学院 
关键词:波纹板 冲压成形 模具设计 正交试验 回弹控制 
分类号:TG386
出版年,卷(期):页码:2023,48(12):57-62
摘要:

研究了波纹板的冲压成形工艺及其回弹控制方法。首先对波纹板进行工艺分析并建立其有限元模型,然后依据仿真结果完成模具结构设计,最后以回弹角为评价指标,基于正交试验研究了冲压速度、摩擦因数和凸模圆角半径等工艺参数对波纹板回弹的影响。极差分析发现,各因素对回弹的影响顺序为:凸模圆角半径>冲压速度>摩擦因数。最终确定最佳的工艺参数组合为:凸模圆角半径为1.8 mm,冲压速度为4 m·s-1,摩擦因数为0.13。通过伺服冲压试验发现,波纹板的回弹角由2.64°降低至1.53°。研究结果表明,所采用的波纹板的成形工艺正确,模具结构设计合理,并且通过工艺参数优化可以有效降低波纹板的回弹。

 The stamping process of corrugated plate and its springback control method were studied. Firstly, the process analysis of corrugated plate was carried out and its finite element model was established, and then the die structure was designed according to the simulation results. Finally, taking the springback angle as the evaluation index, based on orthogonal test, the influences of process parameters such as stamping speed, friction factor and punch fillet radius on the springback of corrugated plate were studied. The range analysis finds that the influencing order of various factors to the springback is as follows: punch fillet radius>stamping speed>friction factor. The best combination of process parameters is the punch fillet radius of 1.8 mm, the stamping speed of 4 mm·s-1 and the friction factor of 0.13. Through servo stamping test, it is found that the springback angle of corrugated plate is reduced from 2.64° to 1.53°. The results show that the used forming process analysis of corrugated plate is correct, the die structure design is reasonable, and the springback of corrugated plate is effectively reduced by optimizing the process parameters.

基金项目:
浙江省重点研发计划项目(2020C01062)
作者简介:
作者简介:刘健(1997-),男,硕士研究生 E-mail:3492607072@qq.com 通信作者:丁明明(1964-),男,硕士,教授 E-mail:dingliumingming@163.com
参考文献:

 [1]上海核工程研究设计院. 一种压水堆蒸汽发生器干燥器用双钩波形板[P].中国:CN201510225440.1, 2015-08-12.


Shanghai Nuclear Engineering Research and Design Institute. A double-hook corrugated plate for steam generator dryer of pressurized water reactor[P]. China:CN201510225440.1, 2015-08-12.


[2]胡海朝,赵淑怡. 基于Dynaform的高强钢U形件回弹影响因素研究[J]. 模具工业,2022,48(4):1-5.


Hu H C, Zhao S Y. Research on influencing factors of springback of high strength steel U-shaped parts based on Dynaform [J]. Die & Mould Industry,2022,48(4):1-5.


[3]王佳坡,鲍梦媛,石宝东,. 先进金属材料制备成形与质量管控理论技术研究[J]. 塑性工程学报,2022,29(10):21-31.


Wang J P, Bao M Y, Shi B D, et al. Theoretical and technological research on fabrication and quality control of advanced metal materials [J]. Journal of Plasticity Engineering, 2022,29(10):21-31.


[4]李艳丽,魏继业,马亚鑫,.扫描速度对激光选区熔化成形304L不锈钢板材高温持久性能的影响[J].精密成形工程,2022,14(9):111-118.


Li Y L, Wei J Y, Ma Y X, et al. Effect of scanning speed on high temperature durability of 304L stainless steel sheet formed by laser selective melting [J]. Journal of Netshape Forming Engineering, 2022,14(9):111-118.


[5]GB/T 20878—2007, 不锈钢和耐热钢牌号及化学成分[S].


GB/T 20878—2007, Stainless and heat-resisting steels—Designation and chemical composition[S].


[6]GB/T 228.1—2021, 金属材料拉伸试验第1部分:室温试验方法[S].


GB/T 228.1—2021, Metallic materials—Tensile testing—Part 1: Method of test at room temperature[S].


[7]张慧妍,刘延辉,宣守强,. 基于Dynaform316L不锈钢拉深成形分析[J]. 模具工业,2021,47(9):1-5.


Zhang H Y, Liu Y H, Xuan S Q, et al. Analysis of deep drawing forming of 316L stainless steel based on Dynaform [J]. Die & Mould Industry,2021,47(9):1-5.


[8]王金荣,涂芬芬,冷志斌,. 基于DYNAFORM的折边机折弯回弹研究[J]. 锻压装备与制造技术,2021,56(1):93-97.


Wang J R, Tu F F, Leng Z B, et al. Research on springback of folding machine based on DYNAFORM [J]. China Metalforming Equipment & Manufacturing Technology,2021,56(1):93-97.


[9]韦钦洋. 钣金V形自由折弯回弹预测研究[D]. 长春:吉林大学,2021.


Wei Q Y. Research on Springback Prediction of Sheet Metal V-shaped Free Bending [D]. Changchun: Jilin University,2021.


[10]祝兴民,莫云霞,何清月,.一种中卡汽车纵梁折弯模具的研发应用[J].锻压装备与制造技术,2022,57(2):78-80.


Zhu X M, Mo Y X, He Q Y, et al. A bending mould research and development of auto longeron card application [J]. China Metabforming Equipment and Manufacturing Technology, 2022,57 (2): 78-80.


[11]孙庆东,张翔,张军,. 基于Dynaform和正交试验的汽车后备箱拉延工艺优化[J]. 现代制造工程,2022,(8):60-64.


Sun Q D, Zhang X, Zhang J, et al. Optimization of car trunk drawing process based on Dynaform and orthogonal test [J]. Modern Manufacturing Engineering, 2022, (8):60-64.


[12]张川,韩永松,陈卫林,. 航空零部件三维扫描与逆向建模[J]. 机械制造,2022,60(7):41-42,54.


Zhang C, Han Y S, Chen W L, et al. Aerospace parts 3D scanning and reverse modeling [J]. Machinery,2022,60(7):41-42,54.


(上接第47页)


[2]程学鹏.冷弯型钢残余应力分布的理论分析与有限元模拟[D]. 武汉: 武汉科技大学,2017.


Cheng X P. Theoretical Analysis and Finite Element Simulation of Residual Stress on Cold-formed Profiled Steel[D]. Wuhan: Wuhan University of Science and Technology,2017.


[3]牛丽丽.超高强度钢辊弯成形工艺变形机理分析[D].北京:北方工业大学, 2017.


Niu L L.The Deformation Mechanism Analysis of the Roll Forming Process for Ultra High Strength Steel[D]. Beijing: North China University of Technology, 2017.


[4]Paralikas J, Salonitis K, Chryssolouris G. Optimization of roll forming process parameters-A semi-empirical approach [J]. The International Journal of Advanced Manufacturing Technology, 2009, 47(9-12): 1041-1052.


[5]Bui Q V, Ponthot J P. Numerical simulation of cold roll-forming processes[J]. Journal of Materials Processing Technology, 2015202: 275-282.


[6]Safdarian R, Moslemi Naeini H. The effects of forming parameters on the cold roll forming of channel section[J]. Thin-Walled Structures,201592: 130-136.


[7]Matthias MonekePeter Groche. Counter measures to effectively reduce end flare [A]. International ESAFORM Conference on Material Forming[C]. Dublin2017.


[8]韩钧,肖爱达,王晓瑜,.高强度工程机械用钢LG700QT 的开发[J]. 辽宁科技大学学报, 2012,35(2):123-125.


Han J, Xiao A D, Wang X Y, et al. Development of high strength engineering machinery steel LG700QT [J]. Journal of University of Science and Technology Liaoning, 2012,35 (2): 123-125.


[9]小奈弘, 刘继英. 冷弯成形技术[M]. 北京:化学工业出版社, 2008.


奈弘ちかん, Liu J Y. Cold Bending Forming Technology [M].Beijing:Chemical Industry Press, 2008.


[10]Halmos G T.冷弯成形技术手册[M].刘继青,艾正青,.北京:化学工业出版社, 2008.


Halmos G T. Cold Bend Forming Technology Manual [M]. Translated by Liu J Q, Ai Z Q.Beijing: Chemical Industry Press, 2008.


[11]李湃.锂电池极片辊压过程轧制力模型研究[D].秦皇岛:燕山大学,2022.


Li P. Research on Rolling Force Model of Lithium Battery Pole Plate Rolling Process [D]. Qinhuangdao: Yanshan University, 2022.


[12]刘晓立.复杂截面超高强钢连续辊弯成型回弹预测与控制研究[D]. 北京: 北京科技大学,2018.


Liu X L. Research on Spring Back Prediction and Control Method of Complex Cross Sectional Ultra High Strength Steel in Cold Roll Forming [D]. Beijing: Beijing University of Science and Technology, 2018.

服务与反馈:
文章下载】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9