网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
加热、轧制、缓冷工艺对60Si2Mn弹簧钢脱碳特性的影响
英文标题:Influence of heating, rolling and slow cooling processes on decarbonization characteristics of 60Si2Mn spring steel
作者:袁林 杨奇军 罗景贤 刘智 王旭冀 
单位:湖南湘潭钢铁有限公司 
关键词:60Si2Mn弹簧钢 脱碳特性 加热 轧制 缓冷 脱碳层深度 
分类号:TG115
出版年,卷(期):页码:2024,49(10):105-111
摘要:

60Si2Mn弹簧钢的脱碳特性与加热、轧制、缓冷工艺紧密相关,通过金相法分析测量60Si2Mn弹簧钢在加热温度为1000~1250 ℃、加热时间为60~300 min、上冷床温度为700~900 ℃、缓冷速率为0.5~3.0 ℃·s-1的工艺条件下的脱碳层深度,并结合硬度分析得到了最佳工艺路线。同时,建立了部分脱碳层深度与加热时间的计算模型。结果表明:部分脱碳层深度随着均热段加热时间的增加而增加,当均热段加热时间为60 min时,部分脱碳层深度在1150 ℃时出现极大值,为48.1 μm;当均热段加热时间>75 min时,加热温度为1200和1250 ℃时的部分脱碳层深度均大于加热温度≤1150 ℃时。部分脱碳层深度随着上冷床温度的降低而降低,缓冷速率对脱碳的影响较小,但随着缓冷速率降低基体热轧布氏硬度降低。得出的最佳工艺为:均热段加热时间为60 min、加热温度为1050 ℃、上冷床温度为700 ℃、缓冷速率为0.5 ℃·s-1,此时基体组织为铁素体和珠光体,部分脱碳层深度为26 μm,硬度为281 HBW。研究结果有助于提高60Si2Mn弹簧钢的生产效率及生产质量。

The decarburization characteristics of 60Si2Mn spring steel are closely related to heating, rolling and slow cooling processes. Therefore, the depth of decarburization layer for 60Si2Mn spring steel in the condition of the heating temperature of 1000-1250 ℃, the heating time of 60-300 min, the upper cooling bed temperature of 700-900 ℃, and the slow cooling rate of 0.5-3.0 ℃·s-1 was measured by metallographic analysis, and combined with the hardness analysis, the optimal process route was obtained. At the same time, a calculation model was established for the depth of partial decarburization layer and the heating time. The results show that the depth of partial decarburization layer increases with the increasing of heating time in the soaking section. When the heating time in the soaking section is 60 min, the depth of partial decarburization layer reaches a maximum of 48.1 μm at 1150 ℃. When the soaking time is greater than 75 min, the depth of partial decarburization layer at 1200 and 1250 ℃ is greater than that at the heating temperature ≤1150 ℃. However, the depth of partial decarburization layer decreases with the decreasing of upper cooling bed temperature, the influence of slow cooling rate on decarburization is relatively small, and the Brinell hardness of matrix decreases with the decreasing of slow cooling rate during hot rolling. The optimal process is the heating time of 60 min in the soaking section, the heating temperature of 1050 ℃, the upper cooling bed temperature of 700 ℃, and the slow cooling rate of 0.5 ℃·s-1. At this time, the matrix structure is ferrite and pearlite, the depth of partial decarburization layer is 26 μm, and the hardness is 281 HBW. Thus, the research results contribute to improving the production efficiency and quality of 60Si2Mn spring steel.

基金项目:
湖南省湘潭市“小荷人才”项目(潭科协发[2022]7号)
作者简介:
作者简介:袁林(1994-),男,硕士,工程师,E-mail:767238701@qq.com
参考文献:

[1]高阳,蓝庆生,孟辉,等.汽车弹簧材料及热处理技术浅析[J].金属加工(热加工),2023(3):88-91.


Gao Y, Lan Q S, Meng H, et al. Brief analysis of automobile spring material and heat treatment technology [J].MW Metal Forming, 2023(3): 88-91.

[2]刘运娜,刘献达.60Si2Mn弹簧钢脱碳行为研究[J].金属热处理,2019,44(S1):115-118.

Liu Y N, Liu X D. The research on decarburization behavior of 60Si2Mn spring steel [J]. Heat Treatment of Metals, 2019,44 (S1): 115-118.

[3]张可,曹明亮,凌孟琪,等. 60Si2Mn弹簧钢表面脱碳研究[J/OL].热加工工艺,1-5[2022-07-13].https://doi.org/10.14158/j.cnki.1001-3814.20210344.

Zhang K, Cao M L, Ling M Q, et al. Study on surface decarburization of 60Si2Mn spring steel[J/OL]. Hot Working Technology, 1-5[2022-07-13].https://doi.org/10.14158/j.cnki.1001-3814.20210344.

[4]于学森,沈奎,江卓俊,等.弹簧钢60Si2MnA表面脱碳规律研究[J].热加工工艺,2017,46(24):224-227,231.

Yu X S,Shen K,Jiang Z J,et al. Study on surface decarburization law of spring steel 60Si2MnA[J]. Hot Working Technology,2017,46(24):224-227,231.

[5]Li H, Zhao X M, Zhang H L, et al. Effect of the oxide layer structure on the decarburization behavior of 60Si2Mn spring steel in dry air: Experimental and first-principle study[J]. Materials Characterization, 2023, 196: 112651

[6]Li P, Wang X X, Ding D D, et al. Surface decarburization depth detection in rods of 60Si2Mn steel with magnetic Barkhausen noise technique[J]. Sensors, 2023, 23(1): 503.

[7]Li H, Zhao X M, Zhang H L, et al. High-temperature oxidation of 60Si2Mn spring steel in dry air and wet air: Insights from an experimental and first-principles study[J]. Steel Research International, 2023, 94(9): 2200691.

[8]权淑丽,郭昭桥,郑开宇,等. 脱碳层深度对弹簧钢 55CrSiA 疲劳性能的影响[J]. 浙江冶金,2015(4):26-28.

Quan S L, Guo Z Q, Zheng K Y, et al. Effect of decarburization layer depth on the fatigue performance of 55CrSiA spring steel [J]. Zhejiang Metallurgy, 2015(4):26-28.

[9]柳洋波,张玮,佟倩,等. 炉气含氧量对弹簧钢 55SiCr脱碳的影响[J]. 金属热处理,2013,38(9):37-41.

Liu Y B, Zhang W, Tong Q, et al. Effect of atmosphere oxygen content on decarburization of 55SiCr spring steel [J]. Heat Treatment of Metals, 2013,38(9):37-41.

[10]李桂英,尹衍成,王思亓,等.弹簧钢60Si2MnA加热工艺对表面脱碳的影响因素分析[J].山东冶金,2022,44(3):27-30,32.

Li G Y, Yin Y C, Wang S Q, et al. Influence factors analysis of surface decarbonization on heating process for spring steel 60Si2MnA [J]. Shandong Metallurgy, 2022, 44(3): 27-30,32.

[11]耿赛晓,耿谊,耿晨尧.高碳钢65Mn脱碳研究[J].甘肃冶金,2014(1):26-29,35.

Geng S X, Geng Y, Geng C Y. Decarburization of high-corbon steel [J]. Gansu Metallurgy, 2014(1):26-29,35.

[12]崔莹莹. CSP生产50CrV4弹簧钢脱碳行为的研究[D].武汉:武汉科技大学,2015.

Cui Y Y. Research on the Surface Decarburization of Spring Steel 50CrV4 by CSP [D]. Wuhan:Wuhan University of Science and Technology, 2015.

[13]余国松,毛文俊,李秦欢,等. 60Si2CrVA弹簧钢轧制过程脱碳的研究[J].浙江冶金,2013(2):33-34.

Yu G S, Mao W J, Li Q H, et al. Research on decarburization during the rolling process of 60Si2CrVA spring steel [J].Zhejiang Metallurgy, 2013(2):33-34.

[14]薛顺,田俊,成国光,等. 新型高铁弹条用弹簧钢的表面脱碳及氧化性能[J].钢铁研究学报,2013(10):47-52.

Xue S, Tian J, Cheng G G, et al. Research on surface decarburization and oxidation of a new type of spring steel for elastic bar of high speed railway [J]. Journal of Iron and Steel Research, 2013(10):47-52.

[15]孙逢源,金涛,李晨潇,等.冷却工艺对弹簧钢脱碳影响的研究[J].特钢技术,2023,29(3):35-37.

Sun F Y, Jin T, Li C X, et al. Study on the effect of cooling process on decarbonization of spring steel [J]. Special Steel Technology, 2023,29(3): 35-37.

[16]赵东宇,雍岐龙,杨庚蔚,等.铌对60Si2Mn弹簧钢表面脱碳敏感性的影响[J].钢铁,2014,49(5):74-80. 

Zhao D Y, Yong Q L, Yang G W, et al. Effect of niobium on surface decarburization sensitivity of 60Si2Mn spring steel [J].Iron and Steel, 2014,49(5): 74-80.

[17]陈被被.汽车悬架弹簧钢脱碳规律的研究[D].马鞍山:安徽工业大学,2016.

Chen B B. Research on Laws of Decarbonization of Automobile Suspension Spring Steel[D]. Maanshan:Anhui University of Technology, 2016.

[18]陈银莉,左茂方,罗兆良,等.60Si2Mn弹簧钢表面脱碳理论及试验研究[J].材料热处理学报,2015,36(1):192-198.

Chen Y L, Zuo M F, Luo Z L, et al. Theoretical and experimental study on surface decarburization of 60Si2Mn spring steel [J]. Transactions of Materials and Heat Treatment, 2015,36 (1): 192-198.

[19]卢新春,罗贻正,王艳林.含硼弹簧钢60Si2Mn的淬透性及其CCT曲线[J].金属热处理,2022,47(12):132-137. 

Lu X C, Luo Y Z, Wang Y L. Hardenability of B containing spring steel 60Si2Mn and its CCT curves [J]. Heat Treatment of Metals, 2022, 47(12): 132-137.
服务与反馈:
文章下载】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9