|
挤压速度对铝型材分流模寿命影响的模拟分析
|
|
英文标题：Simulation analysis of extrusion speed influence to porthole die life |
|
作者：庞祖高 张银意 唐志强 丁洋 |
|
单位：广西大学机械工程学院 |
|
关键词：铝型材 挤压速度 数值模拟 早期失效 |
|
分类号：TG379 |
|
出版年,卷(期):页码：2010,35(1):142-145 |
|
摘要：
|
|
挤压速度是影响铝型材分流模寿命的主要因素之一。不同挤压速度下,模具所受温度和压力不同,对模具寿命产生直接影响。以矩形管铝型材挤压为例,利用Deform有限元分析软件对挤压过程进行数值模拟,得到不同挤压速度下分流模温度和压力变化情况。结果表明:随挤压速度的增大,分流模各工作部位温度逐渐升高,而所承受压力则先降低后升高。探讨了温度和压力的改变对模具寿命的影响机制,指出挤压速度对模具寿命的影响表现为加速模具各工作部分的塑性变形、磨损和应力集中部位失效,以及加剧挤压模的冷热疲劳现象。
|
|
Speed is one of the main factors to affect the life of aluminum extrusion porthole die.At different extrusion speeds,mold temperature and pressure are different,and such situations have a direct impact on the die life.Taking aluminum extrusion rectangular tube as an example,extrusion process of porthole die was simulated by finite element software Deform,and the regularity for change of porthole die temperature and pressure was obtained.The results show that with velocity increases,the temperature of porthole die working parts gradually increases,and the pressure reduces at first than gradually increases.The mechanism of temperature and pressure change affecting the die life was studied.It is pointed out that the influence of extrusion velocity affecting die life can accelerate plastic deformation,wearing of porthole die working parts and failure of stress concentration parts,and also can intensify the heat and cold fatigue phenomenon of porthole die.
|
|
基金项目：
|
|
有色金属及材料加工新技术教育部重点实验室开放基金(GXKFJ-13)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]彭必友.铝型材挤压模具工作状况的数值模拟[D].成都:西华大学,2004.
[2]郑军.挤压模具工作状况的数值分析和模拟[D].成都:四川工业学院,2003.
[3]吴向红,赵国群,孙胜,等.挤压速度和摩擦状态对铝型材挤压过程的影响[J].塑性工程学报,2007,14(1):36-41.
[4]郭志斌,邓小民,张军.空心型材分流模优化设计的有限元模拟[J].模具技术,2008,(4):35-39.
[5]贾俐俐.挤压工艺及模具[M].北京:机械工业出版社,2004.
[6]Gouveia B P P A,Rodrigues J M C,Martins P A F.Steady-state finite-element analysis of cold forward extrusion[J].Jour-nal of Materials Processing Technology,1998,73,281-288.
[7]刘静安,邵莲芬.铝合金挤压工模具典型图册[M].北京:化工工业出版社,2008.
[8]刘汉武,丁桦,崔建忠.铝型材挤压分流组合模有限元分析与计算[J].模具工业,1999,25(4):9-11.
[9]庞祖高,苏广才,林松,等.H13钢温挤压模具型腔开裂失效分析与控制[J].模具工业,2008,34(11):68-71.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
