|
摘要：
|
|
采用双流浇注连续铸造方法,通过改变内浇包熔体温度制备了7075/6009合金铸锭。重点研究了不同内浇包熔体温度下所制备的7075/6009铸锭经过自由压制和轧制变形后的组织和性能。结果表明:7075/6009合金板材在轧制和热处理状态下,当内浇包熔体浇注温度从680℃升高到780℃时,其抗拉强度、屈服强度都会提高,而伸长率变化较小,这主要是由于内浇包熔体温度升高,导致外层合金厚度减小,内层合金在复合材料中的体积分数增加。合金板材在T6热处理状态下获得的最优力学性能是:抗拉强度为404 MPa,屈服强度为364 MPa,伸长率为15.3%。
|
|
The ingots of 7075/6009 aluminum composites were prepared by adjusting the temperature of ladle inside melt from 680℃,730℃ to 780℃ in double-stream-pouring continuous casting.The ingots were then deformed by free hot compression and hot rolling.The effects of pouring temperatures of the melts inside ladles on macro- and micro-structure and tensile property of the 7075/6009 aluminum composite plates were studied.The results show that the tensile strength and yield strength of the rolled and heat-treated sheets increase,however,the elongation of the sheets has little change when the temperatures of the melt in inside ladle increase from 680℃ to 780℃.This occurrence is attributed to the decrease of the thickness of the external layer and the increase of the volume fraction of the internal 7075 alloy with the increase of the melt temperature inside ladle.The optimal tensile property of 7075/6009 aluminum composite plates under T6 condition is that the ultimate strength,yield stress and elongation are 404MPa,364MPa and 15.3% respectively.
|
|
基金项目：
|
|
国家自然科学基金资助项目(50575076,50710105075)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]Zhang Weiwei,Zhu Cangshan,Wei Xingzhao,et al.Thedouble-stream-pouring technique for production gradient ma-terials by continuous casting[J].Chinese Science Bulletin,1998,34(11):911-914.
[2]张卫文,郁鸽,李元元,等.采用连续铸造方式制备的梯度材料[J].材料导报,2000,14(3):24-25.
[3]张卫文,邹敢峰,邓长宁,等.以连续铸造方法制备梯度材料的实验研究[J].金属学报,1998,34(6):610-614.
[4]Li Yuanyuan,Fei Jin,Chen Weiping,et a.lPreparation of2024/3003 gradient materials by semi-continuous castingusing double-stream-pouring technique[J].Cent.SouthUniv.Technol.(English Edition),2002,9(4):229-234.
[5]张卫文,黄强,郑小平,等.内浇包熔体温度对7075/6009梯度合金组织性能的影响[J].铸造技术,2008,29(7):900-904.
[6]张卫文,朱仓山,魏兴钊,等.半连续铸造法制备AlCu/Al梯度材料[J].中国有色金属学报,2002,12(1):188-191.
[7]崔忠圻.金属学与热处理[M].北京:机械工业出版社,2000.
[8]张国定.金属基复合材料[M].上海:上海交通大学出版社,2003.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
