|
摘要：
|
|
在汽车覆盖件拉深成形中,拉延筋可以在较大范围内调节和控制板料的变形程度和变形分布,抑制多种成形质量问题的产生。其中,拉延筋几何参数起着重要的作用。本文以矩形拉延筋为例,建立了拉延筋约束阻力计算有限元模型,对拉延筋几何参数与约束阻力之间的关系进行分析研究。结果表明:拉延筋约束阻力与凹槽圆角半径和凸筋圆角半径成反比,与筋高成正比。结合某轿车B柱加强板实例,通过优化其拉延筋结构参数,得到当1号等效拉延筋高8mm、凸筋和凹槽圆弧半径3mm;2号等效拉延筋高4mm、凸筋和凹槽圆弧半径6mm时,该制件成形质量达到最佳。
|
|
The drawbead plays a very important role in automobile covering part forming processes. The blank deformation size and deformation distribution can be controlled in large range by using drawbead,and many kinds of quality problems from forming processes,such as crack,wrinkle,distortion,etc. can be restrained. The geometry parameter of the drawbead can have an important effect on the processes. Rectangle drawbead was taken as an example to establish the restraining force FEA calculating model. And the analysis of the relationship between the geometry parameter of drawbead and the restraining force was done here. The result indicates that the restraining force of drawbead is in inverse proportion to the radius of the concave groove and the convex drawbead,while the restraining force is in direct proportion to the height of the drawbead. Combined with a car B-column strengthened sheet,the geometric parameters of drawbead were optimized. The best forming quality could be obtained when some of the geometry parameters were set as follows:The height was 8 mm and the circle radius of concave grove and convex drawbead was 3 mm of equivalent drawbead 2#; the height was 4 mm and the circle radius of concave groove and convex drawbead was 6 m of equivalent drawbead 1#.
|
|
基金项目：
|
|
国家自然科学基金资助项目(50275100);;
校人才引进基金(R0820103)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]Ghoo B Y,Keum Y T.Expert drawbead models for sectional FEManalysis of sheet metal forming process[J].Journal of Materials Processing Technology,2000,105(1):17-16.
[2]崔令江.汽车覆盖件冲压成形技术[M].北京:机械工业出版社,2003.
[3]林忠钦.车身覆盖件冲压成形仿真[M].北京:机械工业出版社,2004.
[4]张士宏,程幸叶,唐杰.汽车覆盖件成形拉深筋的有限元模拟与优化[J].锻压技术,2008,33(6):140-143.
[5]马荣国,邱晓刚,廖丕博.实际拉深筋与等效拉深筋的对比研究[J].锻压技术,2008,33(3):36-38.
[6]陈文琳,王世东,朱玉生,等.拉延筋约束阻力的数值模拟研究[J].塑性工程学报,2008,15(1):182-187.
[7]李海波,韩利芬,刘静珏.基于CAE的拉延筋布置对板料成形质量的影响研究[J].塑性工程学报,2007,14(5):18-22.
[8]Weidemann C.The blankholding action of drawbeads[J].Sheet Metal Industries,1978,(9):984-989.
[9]郭华英.拉深筋的力能特性及对板材后续成形影响的研究[D].秦皇岛:燕山大学,2005.
[10]李金燕,傅建,彭必友,等.基于数值模拟的等效拉延筋设计与优化[J].塑性工程学报,2007,14(5):14-17.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
