|
板料单点渐进成形数值模拟研究
|
|
英文标题：Numerical simulation of sheet metal incremental forming |
|
作者：李湘吉 李明哲 蔡中义 |
|
单位：吉林大学辊锻工艺研究所 |
|
关键词：板料 渐进成形 数值模拟 |
|
分类号：TG301 |
|
出版年,卷(期):页码：2009,34(4):79-83 |
|
摘要：
|
|
板料单点渐进成形过程变形复杂、影响因素多,工艺参数选择是提高成形质量和成形效率的关键。对单点渐进成形过程进行数值模拟,分析了成形件的应力分布和厚度变化以及成形路径、进给量等工艺参数对成形过程的影响。结果表明:成形件最大应力和最大厚度减薄发生在底面附近;采用螺旋进给方式可有效提高成形质量和成形效率。实验结果显示,实验结果与数值模拟结果基本吻合。
|
|
For the complex distortion and the numerous influence factors in single point incremental forming process of sheet metal,the process parameter selection is the key to improve forming quality and forming efficiency.Single point incremenal forming process was studied by finite element method,and the distribution of stress and the changing tendency of thickness were analyzed,through the numerical simulation on different amount of feed and forming paths,the effect of forming path and feed on forming result were obtained.The simulated results indicate that the maximum stress and the minimum thickness of cone parts occur at the bottom surface,and the spiral tool path can improve the forming ability and the forming quality.Incremental test shows that the numerical simulation results agree with the experimental results.
|
|
基金项目：
|
|
国家自然科学基金资助项目(50605028);;
吉林大学“985工程”资助项目
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]Li Mingzhe,Cai Zhongyi,Liu Chunguo.Flexible manufac-turing of sheet metal parts based on digitized-die[J].Robot-ics and Computer-Integrated Manufacturing,2007,23:107-115.
[2]周六如,莫建华,肖祥芷.板料零件数控渐进成形工艺研究[J].塑性工程学报,2003,10(4):27-29.
[3]朱虎,姜在宽.基于数控机床的金属板材无模单点渐进成形研究[J].锻压技术,2007,32(2):88-89.
[4]Kitazawa K,Kobayashi M,Iida M.Development of com-puter controlled orbital rotary forming machine and its appli-cation to tube end flanging[J].Journal of the Japan Societyfor Technology of Plasticity,1992,380(33):1080-1083.
[5]戴昆,苑世剑,王仲仁,等.轴对称件多道次数控点成形过程的理论分析[J].塑性工程学报,1998,5(2):26-32.
[6]Jeswiet J,Hagan E.Forming parameters for incrementalforming of aluminium alloysheet metal[J].Proceedings ofthe Institution of Mechanical Engineers B,Journal of Engi-neering Manufacture,2002,(216):1367-1371.
[7]Attanasio A,Ceretti E,Giardini C.Opti mization of toolpathintwo pointsincremental forming[J].Journal of Mate-rials Processing Technology,2006,(177):409-412.
[8]Yamashita M,Gotoh M,Atsumi S Y.Numerical si mulationof incremental forming of sheet metal[J].Journal of Materi-als Processing Teghnology,2008,(199):163-172.
[9]Kopac J,Kapus Z.Incremental sheet metal forming on CNCmilling machine-tool[J].Journal of Materials ProcessingTeghnology,2005,(162-163):622-628.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
