锻压技术

凸轮轴楔横轧成形仿真与应力应变分析

英文标题：Numerical shaping simulation and stress-strain analysis of cam shaft cross wedge rolling

作者：胡福生王宝雨胡正寰

关键词：凸轮轴楔横轧有限元

分类号：TG335.19

出版年,卷(期):页码：2009,34(1):65-68

摘要：

提出了一种凸轮轴楔横轧成形新工艺,得出了楔横轧成形凸轮轴轧辊的辊形曲线和轧齐曲线。利用三维有限元软件DEFORM-3D对凸轮轴成形进行了数值模拟,在模拟轧制过程中,轧辊楔面排料的同时轧件上的凸轮轮廓也被轧辊上的凸轮凹槽逐渐轧制生成,并且逐渐被轧齐,得出轧件应力、应变场在凸轮顶端和芯部较小,在与轧辊楔面接触处最大,呈非对称分布的特点。模拟结果表明,用楔横轧工艺轧制凸轮轴是完全可行的。

A new technology of cam shaft formed by cross wedge rolling was put forward.The roller profile and shaping curves of tools were obtained.The cross wedge rolling deformation process of the cam shaft was simulated with three-dimension finite element soft DEFORM-3D using rigid-plastic finite element method.During the process of simulating roll,the contour of the cam was gradually generated by cam groove while roller wedges were operating material discharge,and the inside right-angle step of rolling work piece was also gradually formed.The position of smaller stress-strain field was occurred at the apex and center of the cam.The maximum value was taken place at the areas between the work piece and the roller,and the total stress-strain field tended to symmetrical distribution.Simulation results indicate that the new technology of cam shaft formed by cross wedge rolling is feasible.

基金项目：

国家自然科学基金资助项目(50675019,50435010);; 北京市自然科学基金资助项目(3082013);; 国家科技支撑计划项目(2006BAF04B03)

参考文献：

[1]张康生,王宝雨,刘晋平,等.楔横轧工艺在内燃机凸轮轴制坯上的应用[J].锻压技术,2000,25(3):28-30.
[2]胡正寰,张康生,王宝雨,等.楔横轧零件成形技术与模拟仿真[M].北京:冶金工业出版社,2004.
[3]白志斌,李东平,洪钟延.汽车刹车蹄片轴的偏心精密成形[J].吉林工业大学自然科学学报,2000,30(4):21-23.
[4]梁继才.轧制非回转体轮廓的楔横轧辊形曲面[J].农业机械学报,1996,27(2):154-156.
[5]梁继才,白志斌,任广升.轧制非圆锻坯的楔横轧机附属装置:中国,94213751.5[P].1994-06-07.
[6]任广升,白志斌,洪钟延,等.楔横轧偏心变形分析与力参数计算[J].吉林工业大学学报,1992,22(3):87-91.
[7]任广升,白志斌,洪忠延,等.楔横轧成形偏心件的条件与相位效应[J].农业机械学报,1992,23(4):71-76.
[8]王宝雨,胡正寰,刘晋平,等.凸轮轴的辊式楔横轧精密成形方法:中国,10112651.5[P].2006-08-28.
[9]何涛,王宝雨,胡正寰.偏心圆截面轴类零件的楔横轧成形数值模拟[J].锻压技术,2008,33(1):53-55.

服务与反馈：

【文章下载】【加入收藏】