网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
高强度板U形件冲压成形的回弹仿真研究
英文标题:Study on computer simulation of spring-back in high strength sheet metal stamping forming
作者:彭伟 杨雪春 杨国泰  
单位:南昌大学机电工程学院 南昌大学机电工程学院 南昌大学机电工程学院 江西南昌330031 江西南昌330031 江西南昌330031 
关键词:高强度板  U形件  纵梁  回弹 
分类号:TG386
出版年,卷(期):页码:2008,33(1):34-38
摘要:
回弹是板料冲压成形过程中一种常见、但又很难解决的现象,在U形件尤其是高强度板U形件的成形中回弹更加明显。分析了回弹机理以及U形件的成形特点,提出采用两次弯曲的办法来控制高强度板U形截面纵梁的回弹,利用有限元分析软件DYNAFORM进行了数值模拟,并且对两次弯曲法进行了实验验证。实验结果表明:模拟正确,采用两次弯曲控制纵梁回弹的工艺方法合理。采用此方法使纵梁的回弹控制在零件的公差范围±1.5mm以内,生产出符合图纸要求的零件。
Spring-back is a phenomenon that is ordinary but difficult to solve in sheet metal stamping formation,which is much more evident to the U-shape part,especially to the high strength U-part sheet metal stamping formation.The spring-back mechanism and its forming characteristic of U-shaped parts in bending forming were introduced.The method of twice bending was introduced to control spring-back in high strength sheet metal carling.Simulation analysis of this method was done by finite element software named DYNAFORM and experiment was also done to certificate this method's correctness.Experimental result shows that the simulation analysis is correct and the method of twice bending to control carling's spring-back is feasible.The carling spring-back is controlled within the range of ±1.5mm of the part tolerance by this method in order to manufacture the parts that can meet the drawing requirement.
基金项目:
作者简介:
参考文献:
[1]钟新农.汽车轻量化与高强度钢板的成形性分析[J].机电产品开发与创新,2006,19(3):40-41.
[2]Liu Gang,Bao Youxia.I mproving di mensional accuracy of u-shaped through an orthogonal design experi ment[J].FiniteElements in Analysis and Design,2002,39:1047-1180.
[3]Karafillis A P,Boyce M C.Tooling design in sheet metalforming using springback calculations[J].Int.J.Mech.Sci.,1992,34(2):113-131.
[4]Finn MJ,Galbraith P C,Wu L,et al.Use of a coupled ex-plicit-i mplicit solver for calculating spring-back in automotivebody panels[J].Journal of Material Processing Technology,1995,(50):395-409.
[5]兰凤崇,陈吉清.U形件拉深成形回弹影响因素的计算机仿真[J].塑性工程学报,2004,11(5):78-84
[6]宋黎,杨坚,黄天泽.板料弯曲成形的回弹分析与工程控制综述[J].锻压技术,1996,21(1):18-22.
[7]林忠钦,刘罡,李淑慧.应用正交试验设计提高U形件的成形精度[J].机械工程学报,2002,38(3):83-89.
[8]陈靖芯,蔡兰,陆国民.车身碰撞盒的回弹试验研究[J].汽车工程,2005,27(1):42-47.
服务与反馈:
文章下载】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9