|
汽车覆盖件成形拉深筋的有限元模拟与优化
|
|
英文标题：Design and optimization of drawbead of automotive panels by FE simulation |
|
作者：张士宏 程幸叶 唐杰 |
|
单位：中国科学院金属研究所 |
|
关键词：有限元模拟 拉深筋 横梁 |
|
分类号：TG386 |
|
出版年,卷(期):页码：2008,33(6):140-143 |
|
摘要：
|
|
利用有限元法模拟某汽车高强钢横梁的成形过程,通过设置拉深筋作为材料流动控制手段。拉深筋的参数设置对成形结果影响很大,首先通过对简单形状零件拉深成形过程的模拟得出一些拉深筋参数对模拟结果的影响规律,然后对横梁拉深筋模型进行多次模拟和修改。通过比较采用等效拉深筋与真实拉深筋模型所得模拟结果,最终得出对于复杂冲压件,应该采用真实拉深筋模型进行模拟的建议。
|
|
The forming process for an automotive underbody cross member was simulated by the FE method.The drawbead was adopted to control the flow of the material.The parameters for drawbead had some effects on the forming process.Firstly,the effect rules of the parameters for drawbead on the simulation results could be obtained by carrying out FE simulation for parts with simple shapes.Then the cross member model was modified for several times according to these rules.By comparing the simulation results obtained by adopting the equivalent drawbead and the real drawbead,the real drawbead model should be used in simulating the stamping process of complex parts.
|
|
基金项目：
|
|
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]赵侠,傅建,余玲.等数值模拟技术在汽车覆盖件成形中的应用[J].锻压技术,2006,31(1):15-21.
[2]马怀波,陈建桥,王书恒.汽车横梁拉深成形的有限元分析[J].润滑与密封,2006,(11):123-126.
[3]郭华英,金淼.板料在半圆形拉深筋中的变形研究[J].锻压技术,2006,31(6):29-32.
[4]陈文亮.板料成形CAE分析教程[M].北京:机械工业出版社,2005.
[5]黄桂美,詹艳然.等效拉延筋模型及其在板料成形数值模拟中的应用[J].现代制造工程,2005,(10):57-58.
[6]胡金华,史艳国,张涛,等.半球形件冲压成形拉深筋影响研究[J].塑性工程学报,2001,8(1):43-46.
[7]雷正保,付爱军,黄冲,等.拉延筋模拟方法对覆盖件CAE结果影响的工业试验[J].汽车工程,2004,26(1):73-77.
[8]徐伟力,林忠钦,刘罡,等.车身覆盖件冲压仿真的现状和发展趋势[J].机械工程学报,2000,36(7):1-4.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
