|
摘要：
|
|
在电磁成形中,成形线圈是使电能变成磁场能,使毛坯产生塑性变形的关键部件。介绍了平板件电磁成形的基本原理,分析了线圈电感对电磁成形效率的影响,以及几种典型的平板线圈电磁力的分布特点和线圈失效的几种基本形式。指出在平板件电磁时,应根据所需成形力的大小和分布来选择和设计线圈,从而提高能量利用率,延长线圈的使用寿命。
|
|
Forming coil is a key part to transform the electric energy into magnetic energy and to make the blank plasticdeformed during the electromagnetic forming.The principle of sheet metal electromagnetic forming was introduced,and the influence of the coil inductance to the forming efficiency,the distribution of electromagnetic force produced by some typical plane coils and the basic failure forms of coils were also analyzed.It is pointed out that in order to increase capacity usage ratio and coilse' life,its selection or design should be in accordance with the distribution and valuation of the forming force needed in sheet metal electromagnetic forming.
|
|
基金项目：
|
|
国家自然科学基金资助项目(50375114);;
塑性成形模拟及模具技术国家重点实验室资助项目(05-03)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]Manish kamal.A Uniform Pressure Electromagnetic Actuatorfor Forming Flat Sheets[D].Ohio,USA:The Ohio StateUniversity,2005.
[2]李春峰.高能率成形技术[M].北京:国防工业出版社.2001.
[3]Peihui Zhang.Joining enabled by high velocity deformation[D].Ohio,USA:The Ohio State University,2005.
[4]Lee Sung Ho,Lee Dong Nyung.Estimation of the magneticpressure in tube expansion by electromagnetic forming[J].Journal of Materials Processing Technology,1996,57(34):311-315.
[5]孟正华,黄尚宇,常宏,等.线圈及集磁器结构对陶瓷粉末电磁压制的影响[J].锻压技术,2006,31(4):138-140.
[6]张守彬,李硕本.电磁成形加工管坯时放电回路参数及放电电流的计算方法[J].锻压技术,1997,22(5):22-24.
[7]于仲连.框架零件电磁成形的研究[J].锻压技术,1993,18(4):25-28.
[8]陆辛.板材高速成形性能及脉冲大电流技术应用研究[D].北京:北京工业大学,2001.
[9]李春峰,赵志衡,李建辉,等.电磁成形磁场力的研究[J].塑性工程学报,2001,8(2):70-72.
[10]黄尚宇,常志华.板坯电磁成形载荷计算方法及分布特性[J].中国有色金属学报,1998,8(3):441-446.
[11]初红艳,费仁元,陆辛,等.平板件电磁成形用线圈的设计[J].中国机械工程,2004,15(22):2031-2036.
[12]初红艳,费仁元,陆辛,等.平板件电磁成形时线圈最小尺寸的计算[J].中国机械工程,2003,14(10):818-822.
[13]霍锋,胡俊伟,余世峰,等.平板件电磁成形工艺研究[J].机械研究与应用,2005,18(6):17-18.
[14]初红艳,费仁元,陆辛.平板件电磁成形的变形模式研究[J].制造技术与机床,2003,(5):28-32.
[15]张杰刚,陈明和.电磁技术在板材成形中的应用[J].新技术新工艺,2006,(9):47-49.
[16]张宝裕,刘恒基.磁场的产生[M].北京:机械工业出版社,1987.
[17]盛熙,曹增强.电磁成形驱动线圈的设计与制造[J].机械科学与技术,2003,22(6):47-48.
[18]杨应平,黄尚宇.电磁成形的物理学原理[J].工科物理,1999,9(5):35-36.
[19]李洪涛,王绍安.电磁成形工艺及其应[J].电加工,1999,(3):36-38.
[20]欧阳伟,黄尚宇.电磁成形技术的研究与应用[J].塑性工程学报,2005,6(3):38-40.
[21]WU Yan-chun,HUANG Shang-yu,CHANG Zhi-hua.Thelow-voltage electromagnetic compaction of powder materials[J].Journal of Wuhan University of Technology MaterialsScience Edition,2002,17(4):39-43.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
