|
摘要：
|
|
采用刚-粘塑性有限元法,基于Deform-3D软件平台,针对铜扁线连续挤压成形过程,进行了三维有限元数值模拟。通过有限元模拟,获得了不同挤压轮转速下铜扁线连续挤压成形过程温度场分布。结果表明,在连续挤压过程中,由于摩擦和变形功的作用,变形体温度逐渐升高。温度的升高主要来自于压实轮的压下和镦粗两个阶段,即温度的升高主要来自于变形功。当挤压轮转速达到1.2564 rad.s-1时,模具回火软化而损坏,从而使挤压过程无法进行。因此,在铜扁线连续挤压过程中,挤压轮转速不能超过1.2564 rad.s-1。
|
|
The continuous extrusion forming(CONFORM) process of copper flat wire was studied by three-dimensional finite-element method based on Software Deform-3D.The rigid-viscoplastic constitutive equation was employed in the model.Distribution of temperature field of copper flat wire continuous extrusion forming was obtained under different extrusion wheel velocities in the forming process.Deformation body temperature was increased remarkably due to friction and deformation power in the CONFORM process.The increased temperature was in the compression wheel press-down and upset stages.So the increase of deformation body temperature was mainly from deformation power.The die could be softened when the extrusion wheel velocity exceeds 1.2564 rad·s-1.So the extrusion wheel velocity should not exceed 1.2564 rad·s-1 in the CONFORM of the copper flat wire.
|
|
基金项目：
|
|
云南省科技攻关项目(2005yx12)
|
|
作者简介：
|
|
|
|
参考文献：
|
[1]宋宝韫,樊志新,陈吉光,等.铜、铝连续挤压技术特点及工业应用[J].稀有金属,2004,28(1):257-261.
[2]Cho J R,Jeong H S.Parametric investigation on the curlingphenomenon in CONFORM process by three-dimensional fi-nite element analysis[J].Journal of Materials ProcessingTechnology,2001,(110):53-60.
[3]钟毅.连续挤压技术及应用[M].北京:冶金工业出版社,2004.14.
[4]Kim Y H,Cho J R,Jeong H S,et al.A study on optimal de-sign for CONFORM process[J].Journal of Materials Pro-cessing Technology,1998,(80-81):671-675.
[5]储灿东,彭颖红,阮雪榆.连续挤压过程的计算机仿真[J].中国有色金属学报,2001,11(s1):48-51.
[6]何升立,张崇高,王心伟,等.Conform连续挤压原理与铜线挤压加工的影响因素[J].工具技术,2005,39(3):27-30.
[7]陈莉,宋宝韫,运新兵.铜扁线挤压模腔内材料成形的数值模拟[J].有色金属(冶炼部分),2004,(1):38-43.
[8]丁志勇.半固态铝合金触变成形的成形特性及数学模型的研究[D].北京:北京有色金属研究总院,2002.
[9]彭颖红,阮雪榆,左铁镛.CONFORM连续挤压耦合热变形过程的刚粘塑性有限元分析[J].中国有色金属学报,1994,4(3):60-64.
[10]应富强,张更超,潘孝勇.金属塑性成形中的三维有限元模拟技术探讨[J].锻压技术,2004,29(2):15.
|
|
服务与反馈：
|
|
【文章下载】【加入收藏】
|
|
|
|
