锻压技术

轿车副车架内高压成形

英文标题：Hydroforming of an engine cradle

作者：苑世剑韩聪刘钢苗启斌王仲仁

单位：哈尔滨工业大学液力成形工程中心哈尔滨工业大学液力成形工程中心哈尔滨工业大学液力成形工程中心哈尔滨工业大学液力成形工程中心哈尔滨工业大学液力成形工程中心 150001 150001 150001 150001 150001

关键词：副车架内高压成形液压成形汽车零件

分类号：U466

出版年,卷(期):页码：2004,29(3):41-44

摘要：

用内高压成形技术在国内首次成功地试制出全尺寸轿车副车架样件 ,经检测尺寸满足设计要求。通过合理的弯曲工艺 ,避免了角部过度减薄引起内高压成形过程中开裂。采用典型截面二维数值模拟和整体零件三维数值模拟相结合的方法 ,给出了合理的预成形坯形状 ,控制壁厚分布和避免终成形合模时在分模面上管材被压出。通过该零件研制 ,基本掌握用内高压成形制造副车架的关键技术

An engine cradle prototype with full size was manufactured successfully by internal high pressure forming (IHPF) in a laboratory of Harbin Institute of Technology. The measure indicated the dimensions of the prototype are corresponding with the design requirements. The excessive thinning at the corners of the workpiece is avoided through a reasonable bending process and then the fracture during IHPF is avoided. A reasonable preform has been designed through the combination of simulation of 2D for typical sections and 3D for the whole part, by which the thickness distribution is controlled and the flash generated from the die parting surface in the final forming is avoided. The key technologies for manufacturing an engine cradle with IHPF are developed basically through the research and experiment of this engine cradle.

基金项目：

参考文献：

1　DohmanF ,HartlC Hydroforming:researchandpracticalapplicationProceedingsof2thInternationalConferenceonInnovationsinHydroformingTechnology,Ohio,USA ,1997
2　KMuammer,TAltanAnoverallreviewofthetubehydroforming(THF)technologyJournalofMaterialsProcessingTechnology2001,108(3):384～393
3　苑世剑,王仲仁内高压成形应用研究中国机械工程,2002,13:783～786
4　JSporer,MDelker,AZisler,TKautzHydroformingatBMW 3rdInter nationalConferenceonHydroforming,Sttugart,Germany,2003:91～110
5　HAbeTheStateoftheArtinTubeHydroformingTechnologyinJapanProceedingsoftheTUBEHYDRO2003,Aichi,Japan,2003:42～43
6　HYKim,HTLim,CHSuhNumericalmodelingoftubehydroformingprocessconsideringprebendingandpreformingeffectProceedingsoftheTUBEHYDRO2003,Aichi,Japan,2003:115～120
7　YuanSJ,WangXS ,LiuG ,WangZR Researchonhydroformingoftubularcomponentswithchangeablecross sectionsProcessingofthe7thICTP ,Yokohama,Japan,Oct27～Nov1,2002:1495～1500
8　YuanSJ,LiuG ,WangXS ,WangZR Useofwrinklesintubehydro forming ideaandexamples3rdInternationalConferenceonHydroforming,Sttugart,Germany,2003:79～90
9　苑世剑,王小松内高压成形机理研究及应用机械工程学报,2002,38:12～15
10　苑世剑,苗启斌,王仲仁不锈钢方形截面空心构件内高压成形研究锻压技术,2004(2)

服务与反馈：

【文章下载】【加入收藏】