锻压技术

LF6合金小锥度铝筒旋压成形实验研究

英文标题：Experimental investigation on spin forming of conical LF6 aluminum alloy tubes with a small angle

单位：中国科学院金属研究所中国科学院金属研究所中国科学院金属研究所中国科学院金属研究所北京航空制造工程研究所北京航空制造工程研究所北京航空制造工程研究所辽宁沈阳110016 辽宁沈阳110016 辽宁沈阳110016 辽宁沈阳110016 北京100024 北京100024 北京100024

关键词：LF6合金小锥度铝筒普旋变薄旋压

分类号：TG376

出版年,卷(期):页码：2005,30(3):43-46

摘要：

介绍了采用圆板坯旋压成形半锥角小于1°的LF6铝合金锥筒的成形试验。试验采用了平板毛坯、直筒与小锥度两套芯模、普旋加强旋的成形方案,在直筒芯模上把圆板坯加热普旋成圆筒,圆筒切底后在室温下对其强旋减薄,最后改用小锥度芯模加热普旋成小锥度筒。结果表明:确保旋前板坯的高质量,避免出现局部缺陷,控制好热旋时的加热温度是能够顺利成形的必要条件;LF6合金具有良好的旋压性能,选择合理的工艺参数,采用圆板坯可以旋压出半锥角小于1°的无缝筒。

Research results of forming LF6 alloy conical tube with half cone angle less than one degree are described in this paper.The forming scheme which utilize slab blank, straight and small coning mandrels, conventional spinning and power spinning is adopted. Firstly, blank is deformed into cylinder with hot conventional spinning in straight mandrel.Then thick-walled tube is forcedly thinned at room temperature after cylinder bottom is cut off. Finally, small coning mandrel and hot conventional spinning are adapted to form conical tube. It can be shown from the results that the ensured blank's high quality before spinning is required to avoid local defect and temperature must be well controlled at hot spinning. LF6 alloy has a good spinning performance. Selecting reasonable technological parameters, seamless conical tube of LF6 alloy with half cone angle less than one degree can be formed by spinning with blank.

基金项目：

参考文献：

[1]赵云豪.角度锥形筒体旋压成形实验研究[C].全国第九届旋压技术交流大会论文集.2002,9:8688.
[2]徐骏,李亚丽,赵云豪.LF6铝合金厚壁简体强力旋压工艺的研究[J].铝加工,1999,22(4):3638.
[3]赵云豪,徐小云.LF6筒形件强力旋压成形[J].金属成形工艺,1990,(4):14.
[4]王振生.变薄旋压产品常见缺陷探讨[J].金属成形工艺,1999,17(2):3133.
[5]王成和,刘克璋.旋压技术[M].北京:机械工业出版社,1986.
[6]陈适先,贾文铎,等.强力旋压工艺及设备[M].北京:国防工业出版社,1986.

服务与反馈：

【文章下载】【加入收藏】