网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
热压缩Ti-4.5Al-3Mo-1V合金的流变应力行为
英文标题:Flow stress behavior of Ti-4.5Al-3Mo-1V alloy during hot compression deformation
作者:宗影影 单德彬 吕炎 
单位:哈尔滨工业大学材料科学与工程学院 哈尔滨工业大学材料科学与工程学院 哈尔滨工业大学材料科学与工程学院 黑龙江哈尔滨150001  黑龙江哈尔滨150001  黑龙江哈尔滨150001 
关键词:Ti-4.5Al-3Mo-1V合金  热变形参数  流变应力  BP网络 
分类号:TG115
出版年,卷(期):页码:2005,30(3):50-52
摘要:
采用Gleeble-1500热模拟机对Ti-4.5Al-3Mo-1V合金在α+β相区进行了等温热压缩实验,根据摩擦修正后的流变应力曲线,研究了此合金在α+β相区恒温压缩时的动态软化规律,分析了热变形参数对该合金流变应力的影响,并采用BP人工神经网络的方法建立了该合金高温变形抗力与应变、应变速率和温度对应关系的预测模型。结果表明:合金的流变应力曲线在低应变速率下达到极值后逐渐软化,在高应变速率下,出现极值后连续振动,然后再逐渐软化的现象;软化的主要机制为动态再结晶;流变应力随温度的升高和应变速率的减小而急剧降低;神经网络方法能够较精确地预测材料的流变应力。
Samples of Ti-4.5Al-3Mo-1V alloy are compressed in α+β phase field on a Gleeble-1500 Simulator. The dynamic softening model in the upsetting process is investigated based on the corrected stress-strain curves. The influences of hot working parameters on the flow stress are systematically studied. A predicting model has been developed by a BP neural network method for the relation between flow stress and deformation strain, strain rate and temperature of Ti-4.5Al-3Mo-1V alloy. The experimental results show that flow curves of the alloy are characterized by a linear increase until regular oscillations at high strain rates or single peak at low strain rates after which flow softening is observed. The softening mechanism is dynamic recrystallization. And the flow stress decreased with increasing temperature and decreasing strain rate. Moreover, the trained network is able to predict the flow stress very accurately.
基金项目:
作者简介:
参考文献:
[1]LiLX.Flowstressbehavioranddeformationcharacteristicsof Ti3Al5V5Mocompressedatelevatedtemperatures[J].MaterialsandDesign,2002,451457.
[2]曹乃光.金属塑性加工原理[M].北京:冶金工业出版社,1983:231235.
[3]林新波,张质良,阮雪榆.利用BP神经网络预测材料温锻流动应力[J].上海交通大学学报.2002,36(4):459462.
[4]LinXB,XiaoHSh,ZhangZL.Flowstressofcarbonsteel08Fintemperaturerangeofwarm forging[J].Journalof MaterialsProcessingTechnology.2003,139(13):543546.
[5]SerajzadehS,TaheriAK.Predictionofflowstressathot workingcondition[J].MechanicsResearchCommunica tions.2003,30(1):8793.
[6]王祖唐,关廷栋.金属塑性成形理论[M].北京:机械工业出版社,1989:143147.
[7]L櫣tjeringG.Influenceofprocessingonmicrostructureandme chanicalpropertiesof(α+β)titaniumalloys[J].Materials ScienceandEngineeringA.1998,243(12):3245.
[8]TakasugiT,WatanabeY,InoueH.Dynamicrecrystallization andsuperplasticdeformationofCo3Ti[J].Scriptamater.2000,43(6):485490.
[9]王科俊,王克成.神经网络建模、预报与控制[M].哈尔滨工程大学出版社,1996:3773.
服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管  中国机械总院集团北京机电研究所有限公司 中国机械工程学会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9