锻压技术

带预制孔筒形件拉深成形金属流动规律的研究

英文标题：Study on metal flow of cylindrical part deep drawing with prefabricate-holes

作者：谭利广肖小亭温华典陈巧玉

单位：广东工业大学

分类号：TG306

出版年,卷(期):页码：2011,36(6):114-119

摘要：

根据带预制孔筒形件成形后侧壁上获得矩形孔的工艺特点及要求，设计了预制孔初始形状为扇形的坯料，采用理论分析和运用ETA/Dyanform软件进行数值模拟实验，深入分析其在拉深过程中的金属变形流动行为的力学机理，分析不同摩擦系数和压边力对金属流动规律的影响。结果表明：预制孔的存在破坏了坯料的完整性，使得孔周围材料的流动发生了显著的变化，通过改变摩擦系数和压边力等参数可以改善成形过程中金属变形和流动的均匀性，并找出利于拉深成形和质量提高的工艺参数。

According to the processing characteristics of getting rectangular holes of the cylindrical part with prefabricate-holes after forming, the blank with prefabricate-holes of sector initial shape was designed. The theory analysis and numerical simulations by using ETA/Dyanform were employed to investigate the mechanical mechanism of the deep drawing process, and to analyze the influence on metal flow by different friction coefficients and blank-holder forces. The results show that the existence of prefabricate-holes destroys the integrity of the blank, the material flow around the hole has changed dramatically, the homogeneity of the deformation as well as metal flow are greatly improved by changing the friction coefficient and the blank-holder force, and the process parameters which will be helpful for deep drawing and promoting the quality are found.

基金项目：

广州经贸委委托项目（2007281）

参考文献：

[1]孙卫和，熊洪淼.带孔件成形过程实验研究[J].南昌航空工业学报，1999,13（1）：53-57.

[2]孙卫和，熊洪淼，韩洪强，等.带孔杯形件成形变形趋向性试验研究[J].锻压技术，2002,27（5）：19-21.

[3]李孝英. 薄料宽凸缘筒形带孔槽拉深件工艺浅析[J].航空工艺技术, 1995 ，(6)：38-39.

[4]赵凌霄，王新伟，胡世光.带孔拉深的极限孔径确定和孔变形分析[J].航天工艺，1997,（4）：10-14.

[5]郭成，秦莹，王长林，等.套筒零件挤压成形金属流动规律研究[J].锻压技术，2008，33（4）：43-47.

[6]Kuang Wei-hua,Xia Qin-xiang,Ruan Feng.3D FEM numerical simulation and experimental study on symmetric thin-wall tube neck-spinning[J].Journal of Harbin Institute of Technology (New Series), 2006, 13(3):315-319.

[7]Ching-Tien Lin,Chin Tarn Kwan. Application of abductive network and FEM to predict the optimal blank contour of an elliptic cylindrical cup from deep drawing[J].Journal of Materials Processing Technology, 2009, 209:1351-1361.

[8]Yang T S. Investigation of the strain distribution with lubrication during the deep drawing process[J].Tribology International, 2010,(43):1104-1112.

[9]王东哲，何丹农，娄臻亮，等.压边力优化控制研究[J].模具技术，2000,（2）：47-51.

[10]胡世光，陈鹤峥.板料冷压成形的工程分析[M].北京：北京航空航天大学出版社，2004.

服务与反馈：

【文章下载】【加入收藏】