网站首页期刊简介编委会过刊目录投稿指南广告合作征订与发行联系我们English
直齿锥齿轮预锻齿形优化设计
英文标题:Gear tooth profile optimization of pre-forging spur bevel gear
作者:邱德花 边翊 钟志平 马晓晖 
单位:北京机电研究所 
关键词:直齿锥齿轮 预锻齿形 数值模拟 物理试验 
分类号:TG316
出版年,卷(期):页码:2012,37(3):7-10
摘要:

基于典型差速器行星齿轮的热冷复合成形工艺,分析了预锻齿形设计的重要性。应用Deform-3D软件模拟不同齿形方案的预锻变形过程,通过数值模拟结果对比分析与物理试验验证,总结出标准预锻齿形与非标准预锻齿形设计的优缺点。若预锻齿形采用标准齿形,精整量较大时在齿根处产生金属折叠,精整量较小时齿面精度低;若预锻齿形采用非标准齿形,即增大齿面冷精整量,减少齿根处冷精整量,热锻件经冷精整后可以达到零件要求,由此确定了非标准预锻齿形为较合理方案。

Hot and cold compound forming process was selected to produce spur bevel gear. The importance of pre-forging gear tooth profile design was stated. Deform-3D software was used to simulate the cold forging process. After analyzing the simulate results and physical experiments, the advantages and disadvantages of standard and nonstandard gear profile were summed up. Using standard gear profile, fold defects exist if the cold finishing amount is large, while the precision of tooth surface is low if cold finishing amount is small. Using nonstandard gear profile, which increases the face finishing amount and decreases the root finishing amount, the defects disappear. Though comparing the results, it is found that the nonstandard hot forging gear tooth profile is better than standard.

基金项目:
国家科技重大专项课题资助项目(2009ZX04013-032)
作者简介:
参考文献:


[1]孙友松. 面向新世纪的塑性加工技术[J]. 锻压技术,2000, 25(2): 12-15.
[2]钟志平,谢谈. 中国温锻技术的现状[J]. 锻造与冲压,2005, (5): 2-4.
[3]权国政,冯福伟,艾百胜,等. 半轴锥齿轮温精锻工艺的数值模拟和实验研究[J].热加工工艺,2008, 37(23):18-21.
[4]张清萍,崔焕勇,王玉增. 锥齿轮精锻成形工艺及有限元分析[J].机床与液压,2009, 37(11):32-33.
[5]夏源. 直齿锥齿轮精锻技术的现状及其发展[J].精密成形工程,2010, 2(6):51-59.
[6]赵军华,莫江涛,成国发,等.直齿锥齿轮精锻技术现状和发展[J].金属加工,2008,(17):14-17.
[7]张猛. 直齿锥齿轮精密锻造生产技术[J].机械工人,2002,(4):24-27.
[8]朱怀沈,夏巨谌,金俊松,等.大模数直齿轮温冷锻精整量的优化选择[J].塑性工程学报,2011,18(1):53-57.
[9]杨慎华,寇淑清,赵勇,等.伞齿轮冷闭塞锻造成形过程数值仿真[J].农业机械学报,2003,24, (2):117-119.

服务与反馈:
本网站尚未开通全文下载服务】【加入收藏
《锻压技术》编辑部版权所有

中国机械工业联合会主管 北京机电研究所有限公司 中国机械工程学会塑性工程分会主办
联系地址:北京市海淀区学清路18号 邮编:100083
电话:+86-010-82415085 传真:+86-010-62920652
E-mail: fst@263.net(稿件) dyjsjournal@163.com(广告)
京ICP备07007000号-9