锻压技术

高精度挤压机中线同轴度实时检测系统研究

英文标题：Study on real-time and high precision extruder midline's coaxiality detection system

作者：全凌云谭建平王宪成小乐

分类号：TG316

出版年,卷(期):页码：2012,37(3):73-77

摘要：

针对目前挤压机挤压中心检测系统精度低、实时性差的问题，设计了一套以PSD（位置敏感探测器）为偏移检测元件的挤压机中线同轴度检测系统，介绍了检测系统的总体方案，建立了同轴度检测的数学模型，阐述了基于镜头成像的偏移检测系统及采用同时采集、打包传输方式的数据传输系统的基本原理，最后通过实验测试了检测系统的基本性能。结果表明，单个活动部件最大检测频率为4Hz，检测精度为0.2mm，重复性好，能够实现挤压机同轴度实时在线检测，提高产品质量。

Aimed at the detecting system of extruder's extrusion center with low accuracy and poor real-time at present，an extruder midline's coaxiality detecting system with PSD (Position Sensor Detector) as offset detect components was designed.The overall plan of detection system was introduced, the mathematical model of the midline detection was established, and the principles of offset detecting system which based on lens imaging and data transfer system which employed simultaneously acquired and packaged transmission were described. At last, the basic performance of detecting system was tested. The results show that the single moving part detecting frequency is 4 Hz and accuracy is 0.2mm, which can detect coaxiality of extruder real-time on-line and improve the quality of products.

基金项目：

国家科技重大专项资助项目（2009ZX04005-031）

参考文献：

［1］陈雪梅. 80MN挤压机挤压筒导向系统改造[J].铝加工，2003,(3):16-18.
［2］谭建平,杨需帅.125MN挤压机挤压中心在线监测系统设计[J].锻压技术，2008,33(5):133-136.
［3］吴士旭.基于图像处理的125MN挤压机对中检测系统设计与研究[D]. 长沙:中南大学,2008.
［4］杨需帅.125MN挤压机挤压中心在线监测系统设计与监测精度分析[D].长沙:中南大学,2008.
［5］孙青林,陈增强,袁著祉，等.焊接钻杆自动对中的检测与控制[J].传感器技术学报，2003,（3）:24-27.
［6］郑二功,李汉强,刘志平.基于二维PSD的任意转角激光对中仪[J].武汉理工大学学报，2006,30(2):358-360.
［7］曹国华,苏成志,徐宏吉.基于位置敏感探测器和激光技术对大型轴系中心先检测方法的研究[J].兵工学报，2006,27(4):765-768.
［8］Hayakawa S,Yamada Y, Tsuchida N. Shaft inserting task into inclined of moving object by using one dimensional PSDs sensor [A]. 8th IEEE International Workshop on Advanced Motion Control[C]. USA：Piscataway, 2004.
［9］黄美珍.位置敏感探测器的研究[D].杭州：浙江大学,2001.
［10］周保玉,陈培锋,朱明珠，等.位置敏感探测器非线性误差修正试验研究[J].光学仪器，2005,27(5):11-15.
［11］管炳良,李星,王俊.二维PSD非线性修正技术研究[J].仪器仪表学报，2007,28(7):1295-1299.

服务与反馈：

【文章下载】【加入收藏】