锻压技术

孔径比为2.50~3.00的自由锻冲孔坯料形状研究

英文标题：Billet shape research of open punching with aperture ratio from 2.50 to 3.00

作者：张如华熊勇勇王师孙雪娇祝岳峰

单位：南昌大学

分类号：TG306；TG316.2

出版年,卷(期):页码：2013,38(1):164-167

摘要：

为消减圆柱坯料自由锻冲孔工件的“走样”缺陷，且高度保持与圆柱坯料冲孔相当，以Φ60 mm×55 mm坯料为例，取孔径比为2.50，2.75和3.00，通过Deform3D软件模拟，得到预成形坯料形状为：外围高度需增加9.1%~3.8%，上端需做出与对应冲子直径之比为27.1%~24.0%的凸起，上端外径基本不变，下端外径需减小14.2%~9.3%，上下端之间呈卡腰状。用预成形坯料冲盲孔及冲穿孔，形状精度明显提高（孔径比为2.50时冲盲孔，工件上端面平面度由6.3mm提高到0.6mm，外侧表面圆柱度由5.9mm提高到0.4mm）。最后进行了物理模拟实验验证，可为实际生产应用提供参考。

n order to reduce the cylindrical billet deformation defects in open punching process and keep its workpiece height nearly unchanged, taking the Φ60 mm×55 mm cylindrical billet as an example, the billet was punched with different aperture ratio of 2.50, 2.75 and 3.00 using the Deform3D software, and the preform billet shape was got that 9.1%3.8% increase is needed in the outside height，a convex top surface with 27.1%24.0% height compared to the corresponding punch diameter is needed in the top surface whose diameter is unchanged, 14.2%9.3% decrease is needed in the bottom surface diameter，and a waistlike side surface is obtained between the top and the bottom surface. All of the blind hole and the through hole workpieces were improved obviously in the shape accuracy when punching the preform billet (the aperture ratio is 2.50, the blind hole workpiece has a flatness of 0.6 mm and cylindricity of 0.4 mm compared to the cylindrical workpiece of 6.3 mm and 5.9 mm respectively). The results were proved by experiment，which can provide references for the practice.

基金项目：

参考文献：

［1］吕炎. 锻造工艺学[M]. 北京：机械工业出版社，1995.
［2］中国机械工程学会锻压学会. 锻压手册：锻造 [M]. 3版.北京：机械工业出版社，2008.
［3］汪大年. 金属塑性成形原理[M]. 北京：机械工业出版社，1982.
［4］林治平，江雄心. 开式冲孔变形过程的计算机模拟——利用上限法模拟非稳定变形过程研究[J]. 南昌大学学报：工科版，1991，13（4）：5-14 .
［5］Akkaram Srikanth, Nicholas Zabaras. Shape optimization and preform design in metal forming processes [J]. Computer Methods in Applled Mechanics and Engineering, 2000, (190): 1859-1901.
［6］Guoqun Zhao, Wright E, Ramara V Grandhi. Sensitivity analysis based preform die shape design for net shape forging [J]. Int. J. Mach. Tools Manuf., 1997, 37(9): 1251-1271.
［7］Guan J, Wang G C, Guo T, et al. The microstructure optimization of Hshape forgings based on preforming die design [J]. Materials Science and Engineering A, 2009(499):304-308.
［8］赵新海，赵国群，王广春，等. 控制锻件变形均匀性的预成形优化设计[J]. 模具技术，2003，（6）：11-20.
［9］纪勇. 加氢直筒节锻造工艺[J]. 大型铸锻件，2008，（5）：23-24.
［10］杨晓禹. 大型空心环类锻件冲孔用十字对中量规设计[J]. 大型铸锻件，2011，（2）：25-26 .

服务与反馈：

【文章下载】【加入收藏】