锻压技术

基于模具变形分析的防撞梁回弹预测精度研究

英文标题：Accuracy study of springback prediction for anti\|collision beam based on die deformation

作者：于强

单位：天津职业技术师范大学

分类号：TG386.3

出版年,卷(期):页码：2013,38(3):54-57

摘要：

以某车型材料为DP780的防撞梁制件及其冲压模具为研究对象，利用有限元数值模拟与试验相结合的研究方法，探讨模具弹性变形对制件回弹预测精度的影响。结果表明：当制件成形时，压边圈与凹模接触压强在0.02～0.04GPa之间，凸模与凹模中心区域的接触压强在0～0.01GPa之间，通过不等间隙型面和理想等间隙型面预测的制件回弹量与实际试模结果相比，前者预测精度误差平均减少17%以上，有效提高了超高强度钢板制件的回弹预测精度。

An anti-collision beam and die were investigated by combination of finite element simulation and tryout methods. The effect of die elastic deformation to springback prediction accuracy was studied. The results show that when panel is formed, the contact pressure between binder and die is 0.02～0.04 GPa and the value is 0～0.01 GPa in the center area between punch and die. Combined with die tryout results, the springback prediction error by simulation with compensated die face is reduced by 17% in average. The simulation method considering die elastic deformation can improve the springback prediction accuracy greatly for ultra high strength steel panels.

基金项目：

天津市应用基础及前沿技术研究计划资助项目（12JCYBJC12600）；天津高校双五科技计划资助项目(SWPY20080003)；天津职业技术师范大学科研计划资助项目（KJ12-13，KJY12-12）

参考文献：

［1］陆宏，黄文. 高强度钢板V 形弯曲板厚方向压缩对回弹的影响[J]. 锻压技术，2011,36（4）:56-59.Lu H, Huang W. Effect of thickness direction compression on springback of high strength V-shape sheet[J]. Forging & Stamping Technology，2011,36（4）:56-59.
［2］刘伟，刘红生，邢忠文，等. 高强钢板冲压成形的回弹规律与工艺参数研究[J]. 材料科学与工艺，2010,18（6）:758-761.Liu W, Liu H S, Xing Z W，et al. Study on process parameters and springback rule for stamping of high strength steel sheet[J]. Materials Science & Technolgy，2010,18（6）:758-761.
［3］徐刚，李建军，付秀娟. 成形速度及载荷对高强钢板回弹影响的研究[J]. 锻压技术，2012,37（2）:15-20.Xu G, Li J J, Fu X J. Research on influence of forming speed and load on springback for high strength steel sheets[J]. Forging & Stamping Technology，2012,37（2）:15-20.
［4］朱阳春，吴向东，万敏，等. 超高强钢板Ｖ形弯曲回弹影响因素有限元分析[J].锻压技术，2012,37（5）:31-34.Zhu Y C, Wu X D, Wan M，et al. Simulation research of V\|bending springback for ultra\|high\|strength steel sheet[J]. Forging & Stamping Technology，2012,37（5）:31-34.
［5］Bekar，Acar，Ozer，et al. Robust springback optimization of a dual phase steel seven\|flange die assembly[J]. Structural & Multidisciplinary Optimization，2012, 46（3）：425-444.
［6］Abdullah A B，Sapuan S M，Samad Z，et al. A comprehensive review of experimental approaches used in the measurement of springback[J]. Advances in Natural and Applied Sciences, 2012，6(2): 195-205.
［7］Aitharaju V, Liu M, Dong J，et al. Integrated forming simulations and die structural analysis for optimal die designs[A]. Numisheet 2005[C].USA:Det roit,2005.
［8］Firat M. Computer aided analysis and design of sheet metal forming processes:Part III: Stamping die\|face design[J]. Materials and Design，2007,28:1311-1320.
［9］Del Pozo D，López de Lacalle L N，López J M. Prediction of press/die deformation for an accurate manufacturing of drawing dies[J]. Journal of Advanced Manufacturing Technology，2008，37：649-656.
［10］Men C F，Yu Q. The full flow of precise die face design process for automobile die[J]. Mechanical Engineering and Materials，2012，153：1427-1430.

服务与反馈：

【文章下载】【加入收藏】