锻压技术

1250mm辊锻机工作部分刚度有限元分析

英文标题：FEM analysis of working part stiffness for 1250 mm roll forging machine

作者：陈杰鹏蒋鹏孙国强

单位：北京机电研究所

关键词：辊锻机有限元线弹性接触分析

分类号：TG334.1

出版年,卷(期):页码：2013,38(3):94-97

摘要：

通过分析辊锻机的工作原理及性能特点，建立了辊锻机工作部分的三维模型。应用有限元软件，采用线弹性和接触分析办法对自主研发的1250mm辊锻机工作部分进行整体有限元分析，综合考虑机架的变形和锻辊的变形，得出了辊锻机锻辊在辊锻过程中的位移分布，其中第3道次最大变形量最大，为1.7269mm。本文计算出了辊锻机的整体刚度，并与通常锻压机械的许用刚度对比得出，1250mm辊锻机的刚度刚度满足设计要求。

Through analysis of the operation principle and features for roll forging machine, a three dimensional model of roll forging machine was built. Based on linear elastic and contact analysis method, the integral finite element analysis method was applied for the working part of self-developped 1250mm roll forging machine. Comprehensively considering the deformation of the rack and roll, the displacement distribution of roll in roll forging process was obtained, and the maximum deformation of the third pass is the biggest with value of 1.7269mm. The whole stiffness of roll forging machine was calculated, compared with working stiffness of metal forming machinery and the stiffness meets the requirements.

基金项目：

北京机电研究所技术发展基金（019083003）

参考文献：

［1］蒋鹏. 我国锻造技术装备60年的进步与发展:下[J]. 金属加工，2010，(13):1-4.Jiang P. The progress and development of 60 years of forging equipment in our country:under[J]. Metal Working, 2010, (13):1-4.
［2］詹会彬，任学平，赵祖德. 轧机刚度的有限元模拟[J]. 塑性工程学报，2007，21(2):50-53.Zhan H P, Ren X P, Zhao Z D. FEM simulation of a rolling mill's stiffness[J]. Journal of Plasticity Engineering, 2007,21(2):50-53.
［3］束学道，胡振寰，邢希东. 楔横轧机刚度边界元有限元耦合新算法[J]. 机械工程学报，2004，40(9):58-61.Shu X D, Hu Z H, Xing X D. Coupling new method of boundary element method and finite element method to calculate cross wedge mill rigidity[J]. Journal of Mechanical Engineering, 2004,40(9):58-61.
［4］束学道，赵静，胡振寰. H1400大型楔横轧机工作机座的结构及设计[J]. 北京科技大学学报，2006，28(4):376-379.Shu X D, Zhao J, Hu Z H. Structure and design of the housing of an H 1400 heavy cross wedge rolling mill[J]. Journal of University of Science and Technology Beijing, 2006,28(4):376-379.
［5］盛蕾，刘军营，高磊. 基于有限元的轧机机架的机械性能分析[J]. 锻压技术，2009，34(1):125-129.Sheng L, Liu J Y, Gao L. Analysis of mechanical behavior of mill frame based on finite element method[J]. Forging & Stamping Technology, 2009,34(1):125-129.
［6］华中工学院等五校.机械传动及曲柄压力机:下册[M].1版.北京：人民教育出版社，1978.Mechanical Transmission and Crank Press Writing Group. Mechanical Transmission and Crank Press:Next Volume[M]. 1st Edition. Beijing: Peoples Education Press, 1978.

服务与反馈：

【文章下载】【加入收藏】