锻压技术

5CrNiMo热作模具钢模块锻造方法的数值模拟

英文标题：Numerical simulation for forging method of die block forging of 5CrNiMo hot die steel

作者：夏琴香范燕波吕明柯赵学智杜玉莲

分类号：TG316

出版年,卷(期):页码：2013,38(5):178-194

摘要：

为保证曲轴模块锻件具有良好的机械性能，常采用平砧对钢锭进行镦粗、拔长、再镦粗、再拔长等多工序方式成形。本文以5CrNiMo热作模具钢曲轴模块锻件为对象，利用有限元软件Deform-3D、对其在8 t电液锤上采用轴向反复镦拔法、径向十字锻造法和综合锻造法等3种不同的锻造方法进行镦粗、拔长、再镦粗、再拔长的全过程进行了数值模拟，分析了3种不同锻造方法锻造后的温度场、应力场和锻造力分布规律。结果表明，采用径向十字锻造法时，其温度场和应力场分布均匀，锻造力较小，锻造过程不易产生裂纹，且锻造操作方法不复杂，为5CrNiMo曲轴模块锻件最合适锻造方法。

To guarantee the good mechanical properties of die block forgings used for crankshaft, the forgings were usually made by the procedures of upsetting, stretching, repeated upsetting and stretching through flat anvil. The whole process simulation of the upsetting, stretching, repeated upsetting and stretching of 5CrNiMo hot die steel under three different forging methods, such as axial repeated upsetting and stretching method, radial cross forging method, integrated forging method on the 8t electro-hydraulic hammer was carried out based on the software Deform-3D, and the distributions of temperature field, stress distribution and forging force were obtained. The results show that when using axial repeated upsetting and stretching method, crack occurs difficultly, the distributions of temperature and stress fields are uniform, the forging load is small, and the forging operation is convenient. It is the best forging method for 5CrNiMo crankshaft die block forging.

基金项目：

夏琴香（1964-)，女，博士，教授

参考文献：

［1］张承峰，赵林武，周预平. MS-3120钢制模块锻件的试制[J]. 大型铸锻件，2007，(6)：26-28.Zhang C F, Zhao L W, Zhou Y P. Trial-anufacture of MS-3120 steeliness module forging[J]. Heavy Casting and Forging, 2007,(6):26-28.
［2］郭会光，田继红.大型锻造的质量和研究方略[J].大型铸锻件，2007,(2)：45-46.Guo H G，Tian J H. The quality control and research program on heavy forging[J].Heavy Casting and Forging, 2007, (2):45-46.
［3］徐尚宝. 4Cr4Mo2WSiV热模具钢的锻造和热处理[J]. 金属加工，1992，(9)：54-55.Xu S B. The forging and heating of 4Cr4Mo2WSiV Hot Die steel[J]. Machinist Metal Forming,1992,(9):54-55.
［4］中国机械工程学会塑性工程学会编.锻压手册1[M].北京：机械工业出版社，2008.China Society for Technology of Plasticity，CMES. Forging and Stamping1[M]. Beijing: China Machine Press, 2008.
［5］夏琴香，向可，赵学智,等.船用长轴类大锻件锻造工艺方法研究[J].锻压技术,2013，38(1): 12-16.Xia Q X, Xiang K, Zhao X Z, et al. Research on forging method of marine long-shaft heaving gorging[J]. Forging & Stamping Technology,2013,38(1):12-16.
［6］任运来,朱磊,聂绍珉,等. 大型锻件锻造镦粗表面无开裂条件[J]. 中国机械工程，2009，20（8）:883-886.Ren Y L, Zhu L, Nie S M, et al. Research on upsetling condition of large forgings upsetting without side surface cracking of ingot[J]. China Mechanical Engineering, 2009，20（8）: 883-886
［7］韩静涛, 薛永栋, 刘均贤. 大型饼类锻件镦粗过程的有限元模拟[J]. 大型铸锻件，2007,（3）:1-7.Han J T, Xue Y D, Liu J X. The finite element simulation of the upsetting process for the heavy pan forgings[J]. Heavy Casting and Forging, 2007,(3):1-7.
［8］张连春, 邓子玉, 曾伟,等. 锻造成形过程中温度场的有限元分析[J]. 沈阳理工大学学报，2005, 24(3): 19-22.Zhang L C, Deng Z Y, Zeng W, et al. Finite element analysis of temperature field during the forging forming process[J]. Transaction of Shenyang Ligong University, 2005, 24(3): 19-22.
［9］任运来, 聂绍珉, 牛龙江,等. 大型锻件锻造拔长新工艺[J]. 机械工程学报, 2007, 43(11): 224-228.Ren Y L, Nie S M, Niu L J, et al. New draw technics of large forges[J]. Chinese Journal of Mechanical Engineering, 2007, 43(11): 224-228.
［10］夏琴香，霍育林，单会星，等.轴类大锻件倒棱滚圆后内部质量及尺寸精度研究[J]. 锻压技术, 2010, 35(2): 17-21.Xia Q X, Huo Y L, Shan H X, et al. Study on internal quality and size precision of long-axis heavy forging after chamfering and rounding[J]. Forging & Stamping Technology, 2010, 35(2): 17-21.

服务与反馈：

【文章下载】【加入收藏】