锻压技术

辊压成形板材表面微结构数值模拟研究

英文标题：Numerical simulation of microstructure on surface of roll forming sheet

作者：胡志清王博王伟 Xun Chen

单位：吉林大学 Liverpool John Moores University

分类号：TG306

出版年,卷(期):页码：2014,39(2):63-67

摘要：

微结构辊压成形技术是耦合了传统的辊压技术与微挤压成形技术的一种新型成形技术，该技术将所需微结构复制到辊表面，然后将辊上的微结构再复印到板材表面。通过有限元对板材微结构辊压成形过程进行数值模拟，对成形阶段及温度在90，120和150 ℃等条件下对成形力的影响进行分析，结果表明：整个辊压阶段，板料发生剧烈塑性变形的范围只集中在板料表层，应变的最大值总是分布在凹槽的底面，板料中间至底部几乎没有应变；同时随着温度升高，稳定成形阶段的载荷值呈降低趋势。通过实验进行了验证，给出了实验结果的局部测量值。

Roll forming microstructure process is coupling with traditional rolling technology and micro-extruding technology. This technology mainly copys the microstructure onto the surface of roller, and then the microstructure on the roller is duplicated on the aluminum sheet. Numerical simulation was used to model the roll forming of microstructure process, and the effect of forming stage and temperature on the forming force at different temperatures of 90，120 and 150 ℃ was analyzed. The results show that there is large plastic deformation concentrated on the subcutaneous sheet, the max value of strain distributes on the bottom of groove, and there is almost not strain on the medium and bottom of sheet. In the meantime, with the increasing of temperature, the load in the stable forming stage decreases. The correlation experimental part was done, and the measure was shown on the local of experimental parts.

基金项目：

国家自然科学基金资助项目（51275201，50905072）；国际合作与交流项目（51311130129）

胡志清（1974-），男，博士，副教授

参考文献：

［1］单德彬，郭斌，周健. 金属薄板微成形技术的研究进展[J]. 塑性工程学报, 2007, 14(3):93-99. Shan Debin, Guo Bin, Zhou Jian. Development in micro forming of thin metal sheet[J]. Journal of Plasticity Engineering, 2007, 14(3):93-99.
［2］Moorear, Lowsonmv. Drag reduction in a rectangular duct using riblets[J] . Aeronautical Journal,1995, 99(5): 187-193.
［3］马欣涛，周建忠，戴亚春. 微型模具及微成形技术的发展[J]. 机械设计与制造， 2005，(12):152-154. Ma Xintao, Zhou Jianzhong, Dai Yachu. The development of micro-mold and microforming technology[J]. Machinery Design & Manufacture, 2005,(12):152-154.
［4］赵清亮，郭兵，杨辉，等. 金刚石飞切加工微结构表面的工艺参数优化[J]. 光学精密工程, 2009, 17(10): 2514-2519.Zhao Qingliang, Guo Bin, Yang Hui, et al. Technological parameter optimization of micro-structured surfaces by diamond fly-cutting[J]. Optics and Precision Engineering,2009,17(10): 2514-2519.
［5］丁智，王立功，王晓慧. 微结构表面车削多轴联动数控系统的研究[J]. 控制工程,2011，18（S1）：18-26. Ding Zhi, Wang Ligong, Wang Xiaohui. On multi-axis CNC system for diamond turning of micro-structured surfaces[J]. Control Engineering of China,2011，18（S1）：18-26.
［6］梁春永, 杨阳, 王洪水, 等. 应用飞秒激光在NiTi合金表面制备多孔微结构[J]. 科学通报, 2008, 53(1): 61-65.Liang Chunyong, Yang Yang, Wang Hongshui, et al. Application of femtosecond laser in the preparation of porous NiTi alloy surface microstructure[J]. Chinese Science Bulletin, 2008, 53(1): 61-65.
［7］刘福超, 雷丽萍, 曾攀. 滚压有限元模型数值模拟[J]. 塑性工程学报, 2012, 19(2): 17-19. Liu Fuchao, Lei Liping, Zeng Pan. Surface rolling FE model for numerical simulation[J]. Journal of Plasticity Engineering, 2012, 19(2): 17-19.
［8］Majzoobi G H，Teimoorial Motlagh S，Amiri A. Numerical simulation of residual stress induced by roll-peening[J]. Transactions of the Indian Institute of Metals, 2010, 63(2): 499-504.
［9］Shan Debin，Wang Chunju，Guo Bin,et al. Effect of thickness and grain size on material behavior in micro-bending[J]. Transactions of Nonferrous Metals Society of China, 2009, 19(2): 507-510.

服务与反馈：

【文章下载】【加入收藏】