锻压技术

一种简化工序的鲤鱼钳锻造工艺

英文标题：A simplified forging process of carp grips

作者：王伟刚程联军

关键词：锻造工艺鲤鱼钳有限元模拟

分类号：TG316

出版年,卷(期):页码：2014,39(3):1-4

摘要：

针对鲤鱼钳传统的锻造工艺进行改进，提出一种新的锻造工艺。该工艺省去了传统工艺的拔长工序，采用圆棒坯料直接终锻的方法。新工艺将传统工艺的一模一件改进为一模两件。进行了终锻模型腔布排和设计，对锻造过程进行了三维有限元模拟，在锻锤上进行了试生产。研究结果表明：新工艺不仅将材料利用率提高了0.5%，而且工艺性好，操作方便，生产效率高。

The new forging process of carp grips was proposed to improve traditional forging process. The cylinder billet was formed directly to the finish-forging part, and the traditional stretching procedure was omitted in this forging process. The forging die with one module and two cavities instead of traditional one module and one cavity was determined. The finish-forging die cavities were arranged and designed. The 3D finite element method (FEM) simulation of the forging process was presented, and experimental studies were performed on the forging hammer. The results show that the material utilization rate is improved by 0.5% in the new forging process, and the new forging process is simple and convenient for operation, meanwhile it has good manufacturability and high production efficiency.

基金项目：

山东省科技发展计划资助项目 (2012YD03111)

参考文献：

［1］张国新. 汽轮机叶片无余块锻造[J]. 锻压技术, 2008, 33(5): 28-30.Zhang Guoxin. No excess metal forging of steam turbine blade[J]. Forging & Stamping Technology, 2008, 33(5): 28-30.
［2］王云飞, 夏占雪, 胡志高, 等. 曲轴先进锻造技术的研究与应用[J]. 锻压技术, 2012, 37(1): 1-5.Wang Yunfei, Xia Zhanxue, Hu Zhigao, et al. Study and application of advanced crank shaft forging technology[J]. Forging & Stamping Technology, 2012, 37(1): 1-5.
［3］胡金华. 特大型船用曲轴曲柄锻造工艺优化研究[J]. 锻压技术, 2010, 35(1): 12-15.Hu Jinhua. Study on process optimization of large-scale crankshafts used for ships[J]. Forging & Stamping Technology, 2010, 35(1): 12-15.
［4］王凯, 王皓, 唐振英, 等. 13B型货车钩尾框框体锻造工艺模拟及优化[J]. 锻压技术, 2013, 38(2): 14-16.Wang Kai, Wang Hao, Tang Zhenying, et al. Forging process and FEM optimization of 13B type forged yoke body for railway wagons[J]. Forging & Stamping Technology, 2013, 38(2): 14-16.
［5］蒋鹏, 韦韡, 付殿禹, 等. 重卡转向节多工步卧式锻造成形过程的数值模拟[J]. 锻压技术, 2010, 35(2): 22-25.Jiang Peng, Wei Wei, Fu Dianyu, et al. Simulation of horizontal multistep die forging for heavy truck steering knuckle[J]. Forging & Stamping Technology, 2010, 35(2): 22-25.
［6］程联军, 赵国群, 杨建华, 等. 有限元模拟在后轴支架锻造设计中的应用[J]. 塑性工程学报, 2008, 15(1): 14-17.Cheng Lianjun, Zhao Guoqun, Yang Jianhua, et al. FEM simulation of forging process for the design of a rear axle bracket[J]. Journal of Plasticity Engineering, 2008, 15(1): 14-17.
［7］赵新海, 程联军, 吴向红, 等. 非对称复杂形状连杆模锻的三维有限元模拟[J]. 模具技术, 2005, (10): 3-5.Zhao Xinhai, Cheng Lianjun, Wu Xianghong, et al. 3D FEM simulation of forging of non-symmetrical and complex connecting rod[J]. Die and Mould Technology, 2005, (10): 3-5.

服务与反馈：

【文章下载】【加入收藏】