锻压技术

铝合金薄板零件一步法橡皮囊成形实验分析

英文标题：Experimental study on one-step fluid cell forming of thin aluminum alloy sheet parts

作者：涂集林王永军惠小鹏邱超斌魏生民

分类号：TG386;V262.3+2

出版年,卷(期):页码：2014,39(6):50-54

摘要：

铝合金薄板零件即浅盆形零件在一步法橡皮囊成形后，盆底和法兰部分分别出现鼓动和松动缺陷。通过对此缺陷进行实验分析，提出改进的一步法橡皮囊成形工艺为：下料水淬矫平橡皮囊成形时效硬化修边，橡皮囊成形需要进行低压和高压二次橡皮囊的包边成形，并采用蒙拉矫平与可矫平0.4 mm板辊式矫平机单独矫平的两种不同的矫平方式进行实验分析对比，蒙拉矫平的预拉量需要控制在1.5%~2%范围内。实验结果表明:采用聚合物淬火液进行淬火的板料变形小；采用可矫平0.4 mm辊式矫平机单独矫平与蒙拉矫平相比，可使鼓动和松动缺陷减小，成品率提高70%。

After one-step fluid cell forming, the shallow basin shaped thin aluminum alloy sheet parts respectively are of defects of bottom buckling and flange buckling. The experimental study on these defects was made, and the one-step fluid cell forming process was proposed as “sheet cutting→water quenching→leveling→fluid cell forming →age hardening →trimming”. The sheet leveling induded two different ways which were skin stretch leveling within 1.5%-2% strain and roller leveler for 0.4 mm sheet leveling. Finally, the experimental results show that the sheet deformation is smaller with the polymer quenching medium; the defects of bottom buckling and flange buckling are reduced with roller leveler for 0.4 mm sheet leveling instead of skin stretch leveling, and the rate of finished product is improved by 70%.

基金项目：

参考文献：

［1］航空制造工程手册总编委会. 航空制造工程手册: 飞机钣金工艺 [M]. 北京：航空工业出版社, 1992.Aeronautical Manufacturing Technology Manual Ehief Ed2 itorial Committee. Aeronautical Manufacturing Technology Manual-Sheet Metal Forming[M]. Beijing: Aviation Industry Press,1992.
［2］傅俊旭. 铝合金板料的新淬火状态与高压柔性成形技术[J]. 航空工艺技术, 1998, (1): 22-23，26.Fu Junxun. As-quenched al alloy sheet and high pressure flexible forming technology[J]. Aeronautical Manufacturing Technology,1998, (1):22-23，26.
［3］Terry Ford. Aerospace materials [J]. Aircraft Engineering and Aerospace Technology, 1994, 66(6): 5-7.
［4］Giuseppe Sala. A numerical and experimental approach to optimise sheet stamping technologies: Part Ⅱ-aluminium alloys rubber-forming [J]. Materials & Design, 2001, 22(4): 299-315.
［5］ASM International Handbook Committee. ASM Handbook: Volume 14[M]. Metals Park, Ohio: ASM International, 2006.
［6］王秋成, 柯映林. 航空高强度铝合金残余应力的抑制与消除 [J]. 航空材料学报, 2002, 22(3): 59-62.Wang Qiucheng, Ke Yinglin. Control and relief of residual stresses in high-strength aluminum alloy parts for aerospace industry [J]. Journal of Aeronautical Materials, 2002, 22(3): 59-62.
［7］梁轩, 彭大暑, 张辉. 7075 铝合金预拉伸板消除残余应力的试验研究 [J]. 轻合金加工技术, 2003, 31(1): 15-17.Liang Xuan, Peng Dashu, Zhang Hui. Experimental study on reduction of residual stress in quenched thick plate of 7075 aluminium alloy [J]. Light Alloy Fabrication Technology, 2003, 31(1): 15-17.
［8］崔甫. 矫直原理与矫直机械 [M]. 北京：冶金工业出版社, 2005.Cui Fu. Straightening and Straightening Machine [M]. Beijing：Metallurgy Industry Press, 2005.
［9］陈磊, 邱晞, 李善良, 等. 橡皮液压凸弯边成形试验与分析研究 [J]. 锻压技术, 2007, 32(6): 58-60.Chen Lei,Qiu Xi, Li Shanliang, et al. Experimental study and analysis on shrink flanging in rubber fluid forming [J].Forging & Stamping Technology, 2007, 32(6): 58-60.
［10］付云方, 高霖, 王辉. 橡皮囊成形的研究进展[J]. 中国制造业信息化, 2009, 38(7): 59-63,66.Fu Yunfang, Gao Lin, Wang Hui. A review of the research on rubber bladder forming [J]. Machine Design and Manufacturing Engineering, 2009, 38(7): 59-63,66.
［11］Kilpatrick W, Brown D,McMurray R J, et al. The effect of serrated yielding on the determination of r-values in aluminium alloys and yield locus calibration [J]. Materials Science and Engineering: A, 2010, 527(29-30): 7557-7564.

服务与反馈：

【文章下载】【加入收藏】