锻压技术

精冲模具在冲压过程中的温升研究

英文标题：Study of die temperature rising in fine blanking process

作者：曹传亮张祥林董春法李正龙

单位：华中科技大学

关键词：精冲有限元模拟模具温度测量

分类号：

出版年,卷(期):页码：2014,39(7):113-117

摘要：

为了研究精冲过程中剪切区温升对模具的影响，设计制造了一副能够安装热电偶以测量精冲过程中模具温度变化的精冲模具，并对4种不同材质板料在实时连续冲裁过程中的模具温度变化进行测量实验。采用基于热力耦合的有限元方法对连续精冲过程的温度变化进行模拟研究，模拟结果显示，精冲塑性好的板料模具温升较小；材料强度越高，料厚越厚，模具温升越大；待测点处温度都是前几次冲压过程快速升高，然后达到稳定状态，这与实际测量结果吻合。该有限元方法能有效预测精冲工艺温度场。

To study the influence of temperature rising in sheared region during fine blanking process on the die, a special fine blanking die fixed with thermocouple to measure the temperature change of die was designed and manufactured. Real-time measurements of the temperature for the die in the continual fine blanking process with four kinds of sheet metal were carried out. The temperature change in the continual fine blanking process was simulated by using coupled thermal-mechanical finite element method. The results show that the temperature rising is smaller when fine blanking the sheet metal with better plasticity. If the tensile strength is higher and the material thickness is thicker, the temperature rising will be bigger. The temperature rises rapidly in the previous blanking processes, then reaches an equilibrium state，which is in accordance with the actual experiment. The temperature field with fine blanking process can be effectively predicted by using the finite element method.

基金项目：

国家科技重大专项“高档数控机床与基础制造装备”(2009ZX04014-073-04)

曹传亮(1986-)，男，博士研究生

参考文献：

[1]周开华. 简明精冲手册[M]. 2版. 北京：国防工业出版社, 2006.

Zhou Kaihua. Fine Blanking Handbook [M]. Second Edition. Beijing：National Defense Industry Press, 2006.

[2]Faura F, García A, Estrems M. Finite element analysis of optimum clearance in the blanking process [J]. J. Mater. Process Technol., 1998, 80(81):121-125.

[3]Fang G, Zeng P, Lou L. Finite element simulation of the effect of clearance on the forming quality in the blanking process [J]. J. Mater. Process Technol., 2002, 122(2-3):249-254.

[4]胡建华，付炳欣，秦建军.小模数齿形精冲的数值模拟及参数优化[J].塑性工程学报，2010，17(1)：52-56.

Hu Jianhua, Fu Bingxin, Qin Jianjun. Numerical simulation and optimization of processing parameters for fine-blanking of fine-pitch gear [J]. Journal of Plasticity Engineering, 2010, 17(1):52-56.

[5]Goijaerts A M, Govaert L E, Baaijens F P T. Prediction of ductile fracture in metal blanking[J]. Journal of Manufacturing Science and Engineering, 2000, 122: 476-483.

[6]余心宏，翟妮芝，翟江波. 基于Oyane韧性断裂准则的板料成形极限预测[J]. 材料科学与工艺, 2009, 17(5): 738-740.

Yu Xinhong, Zhai Nizhi, Zhai Jiangbo. Prediction of the forming limit of sheet metals based on Oyane ductile fracture criterion[J]. Materials Science & Technology, 2009, 17(5): 738-740.

[7]谢晓龙，赵震，虞松，等. 基于Oyane损伤和断裂模型的厚板精冲过程数值模拟和缺陷预测[J]. 上海交通大学学报，2006，40（6）：927-931.

Xie Xiaolong, Zhao Zhen, Yu Song, et al. The numerical simulation and failure prediction for thick sheet metal fine-blanking based on Oyane damage and fracture model [J]. Journal of Shang Hai Jiaotong University, 2006, 40(6):927-931.

服务与反馈：

【文章下载】【加入收藏】