锻压技术

热模锻液压机滑块动作回路设计

英文标题：Action circuit design for slider in hot die forging hydraulic press

作者：王勇

单位：太原重工股份有限公司

分类号：TG315.4

出版年,卷(期):页码：2014,39(8):65-68

摘要：

介绍了热模锻液压机的结构、主要性能参数和使用要求，设计出滑块动作回路，并详细论述了其组成部分的工作原理。回路的集成控制阀块采用二通插装阀控制油路中的油流方向、压力和流量，具有流阻小、响应快、内泄漏少、启闭特性和过载保护性能好的特点。采用比例柔性泄压技术将比例溢流阀的设定压力按一定曲线缓慢调整为0，达到缓慢卸压的目的，使压机运行平稳，降低震动和噪音；并设有防止滑块支承失效的双阀支承阀组及可靠的压力安全保险装置，使滑块动作可靠和稳定。各控制阀按程序动作，实现滑块0～15 mm·s-1工作速度的无级可编程控制，压机效率可提高到40 s完成一次压制循环，满足设备使用和各项性能参数的要求。实践证明设计合理、性能可靠，可在相关行业上使用。

The structure, main performance parameters and operating requirement of hot die forging hydraulic press were introduced, a slider action circuit was designed and the working principle of its constitution was detailed discussed. The two-port cartridge valve was used as integrated control valve block circuit to control the flow direction, pressure and flow of oil, which has merits of small flow resistance, quick response, less leakage, opening and closing characteristics and good overload protection performance. The proportion of flexible pressure relief technology was used to slowly adjust the setting pressure of proportional overflow valve to be 0 according to a certain curve, which can unload pressure, thereby, the compressor runs smoothly, and the vibration and noise reduce. A double valve supporting valve group was used to prevent the slider bearing failure, and there was reliable pressure safety device, so that the slider action was reliable and stabile. Each control valve acts with order to achieve stepless programmable control of slider with 0-15 mm·s-1 working speed and compressor efficiency can get to 40 s to complete a pressing cycle, which meet the requirements of equipment use and various performance parameters. Practice proves that the design is reasonable, performance is reliable, and it can be used in related industries.

基金项目：

山西省科技创新项目（2013101012）

王勇（1984-），男，本科，工程师

参考文献：

［1］郝尚清, 薛峰.中国首台横向预紧板框式液压机-60 MN轮毂热模锻压力机[J]. 锻压装备与制造技术, 2006，41（4）:29-31. Hao S Q, Xue F. Chinese first transverse pre-tightening plate frame hydraulic press -60MN wheel hub hot die forging hydraulic press[J]. China Metal Forming Equipment & Manufacturing Technology, 2006，41（4）:29-31.
［2］俞新陆. 液压机的设计与应用[M]. 北京: 机械工业出版社, 2006. Yu X L. Design and Application of Hydraulic Machine[M]. Beijing: China Machine Press,2006.
［3］刘小群, 吴启仁. 机械设计基础[M]. 北京: 人民邮电出版社, 2007. Liu X Q, Wu Q R. Fundamentals of Mechanical Design[M]. Beijing: Peoples Posts and Telecommunications Press, 2007.
［4］刘延俊，关浩，周德繁. 液压与气压传动[M]. 北京: 高等教育出版, 2007. Liu Y J, Guan H, Zhou D F. Hydraulic and Pneumatic Transmission [M]. Beijing: Higher Education Press, 2007.
［5］范玉林, 张营杰, 卫凌云, 等. 45/50 MN快锻油压机液压系统设计分析[J]. 锻压装备与制造技术, 2011，46（5）：49-51. Fan Y L, Zhang Y J, Wei L Y, et al. Design and analysiso fhy draulic system for 45/50MN hispeed forging hydraulic press[J]. China Metal Forming Equipment & Manufacturing Technology, 2011，46（5）：49-51.
［6］张新国. 大吨位精整压力机快速返程时惯性冲击原因分析及对策[J]. 锻压装备与制造技术, 2012，47（2）：14-16. Zhang X G. Developing status and trend of forging manipulator[J]. China Metal Forming Equipment & Manufacturing Technology, 2012，47（2）：14-16.
［7］路甬祥. 液压气动手册[M]. 北京: 机械工业出版社, 2005. Lu Y X. Hydraulic and Pneumatic Manual [M]. Beijing: China Machine Press, 2005.
［8］林峰, 颜永年，吴任东,等. 现代重型模锻液压机的关键技术[J]. 机械工程学报, 2006，42（3）:9-14. Lin F, Yan Y N, Wu R D, et al. Key technologies of modern heavy die forging press[J]. Journal of Mechanical Engineering,2006，42（3）:9-14.
［9］湛利华，沈文奇，陈敏，等. 大型模锻压机卸压回路仿真研究[J]. 锻压技术，2013，38(1)：80-84. Zhan L H, Shen W Q, Chen M, et al. Simulation research on pressure relief loop for large die-forging hydraulic press[J]. Forging & Stamping Technology, 2013，38(1):80-84.
［10］刘忠伟, 刘少军，黄明辉. 巨型模锻液压机同步控制系统控制性能影响因素研究[J]. 锻压技术, 2010，35（5）:68-72.Liu Z W, Liu S J, Huang M H. Influence factors research on control performance of synchronous control system for giant forging hydraulic press [J]. Forging & Stamping Technology, 2010，35(5):68-72.

服务与反馈：

【文章下载】【加入收藏】