锻压技术

压力机机身特厚板组合件焊接路径优化

英文标题：Optimization on welding path of super-thick plate assembly part for press frame

分类号：TG315

出版年,卷(期):页码：2014,39(12):83-86

摘要：

根据厚板焊接时热量的传递特性，利用热弹塑性有限元法和并行计算技术并借助先进的CAE分析软件对160 t C型压力机机身特厚板组合件进行热-力耦合计算和焊接路径优化。首先采用hypermesh软件进行网格划分，建立有限元模型；然后选用最接近二氧化碳电弧焊熔池精度的恒温三维双椭球热源模型，建立最接近现场的边界条件，并使用并行计算进行模拟；最后通过变形计算结果分析获得了最佳的焊接工艺方法。结果表明，对厚板相邻两边的K形焊缝施焊时，要保证对每一边第一道焊均处于板的同侧；对组合件焊接时，先对结构进行打底焊然后在进行盖面焊，其焊接变形最小。

According to the heat transfer characteristics of welded plates, the numerical simulation on the thermal-mechanical couple and the optimization of the welding path were performed on the 160 t C-type super-thick plate assembly part of press frame by the elastic-plastic finite element method, parallel computing technology and the advanced CAE software. First, finite element model was established and meshed by hypermesh software. Then, 3D double ellipsoid heat source model with constant temperature which is the closest to welding pool accuraty of the CO2 arc was chosen, and the boundary conditions which are the closest to the actual boundary were chosen, and the simulation was realized by the parallel computing. Finally the optimum method of welding was obtained by analyzing the results of deformation calculation. The results show that when K-shaped seam of adjacent two sides of the plate is welded, it is necessary to ensure that the first-pass welding seam on each side of the plate is in the same side, however, when assembly workpieces are welded, backing weld of the structure should be performed first and then that of the capping in order to obtain the smallest welding deformation during welding.

基金项目：

广东省战略性新兴产业核心技术攻关项目资助(2012A090100014)

胡浩（1987-），男，硕士研究生

参考文献：

[1]史宝君,唐晓阳,王保岭.开式压力机机床身有限元分析与结构优化[J].力学与实践,2000,（22）:35-38.

Shi B J, Tang X Y, Wang B L. Finite element analysis and structure optimization for open-press fuselage[J]. Pressure & Practice, 2000,(22):35-38.

[2] 张祖芳,仲太生,许超.开式压力机机身轻量化设计研究[J].锻压装备与工业炉,2003,(3):26-28.

Zhang Z F, Zhong T S, Xu C. Lightening design research of openback press frame[J]. Metalforming Equipment & Industrial Furnace, 2003,(3):26-28.

[3]田锡唐. 焊接结构[M]. 北京: 机械工业出版社, 1982.

Tian X T. Welded Structures[M]. Beijing: China Machine Press, 1982.

[4]方洪渊.焊接结构学[M].北京：机械工业出版社，2008.

Fang H Y. School of Welded Structures[M]. Beijing: China Machine Press, 2008.

[5]陈建波,罗宇,龙哲.大型复杂结构焊接变形热弹塑性有限元分析[J].焊接学报，2008,29(4):69-72.

Chen J B, Luo Y, Long Z . Analysis on welding distortion of large complicated structure by thermal elastic-plastic finite element method[J]. Transactions of the China Welding Institution, 2008,29(4):69-72.

[6]周广涛,刘雪松,闫德俊,等.顶板焊接顺序优化减小焊接变形的预测[J].焊接学报,2009,30(9):109-112.

Zhou G T, Liu X S, Yan D J, et al. Prediction for welding deformation reducing by welding sequence optimization of upper plate[J]. Transactions of the China Welding Institution, 2009,30(9):109-112.

[7]周广涛,胡继超,方洪渊.动臂梁焊接顺序优化减少焊接变形模拟预测[J].计算机辅助工程,2013,22(5):96-100.

Zhou G T, Hu J C, Fang H Y. Simulation and prediction for welding deformation reducing by welding sequence optimization of movable arm beam[J]. Computer Aided Engineering,2013,22(5):96-100.

服务与反馈：

【文章下载】【加入收藏】