锻压技术

前副车架上板冲压工艺及拉延模设计

英文标题：Stamping process and drawing die design of upper plate for the front subframe

作者：林泉刘驰

单位：柳州职业技术学院

关键词：前副车架上板冲压工艺拉延模

分类号：

出版年,卷(期):页码：2015,40(4):45-48

摘要：

汽车前副车架上板料厚3.5 mm，型面变化复杂，有多处凹凸面，装配孔与其他零件装配精度要求高，零件成形难度较大。制定了五工序的冲压工作内容，其中拉延为最重要的成形工序。其工艺方案的关键技术是采用工艺凸包，防止转角在拉延时开裂。针对前副车架上板的材料厚度大、形状复杂、材料流入困难的问题，在内外压边圈均不设拉延筋，使成形得以顺利进行。应用AutoForm软件对前副车架上板进行成形仿真分析，通过多次调整压料面、工艺补充面、圆角、板料外形、压边力，得到了优化后的拉延工艺数模，并生产出质量合格的产品,验证了冲压工艺改进的有效性。

The upper plate of car front subframe of 3.5 mm thickness has complicated variation and contoured surface, and it is difficult to form because the assembly accuracy requirement between assembly hole and other parts is high. In the design, five processes of stamping were formulated，and the drawing process was the most important forming process. Its key technology was to adopt the craft convex hull to prevent cracking from the corner during drawing process. For the problems of large thickness of material，complicated shape and difficulty in inflowing of material for upper plate of the front subframe, the drawbeads were not set on the inside or outside blank holder, so that the forming can be carried out smoothly. The forming process of upper plate was simulated by AutoForm software，and the optimized drawing process model was obtained through adjusting the binder surface, addendum surface, rounded, sheet shape and blank holder force repeatedly. Therefore, the qualified products were produced, and the effectiveness of stamping process improvement was verified.

基金项目：

2012年度广西教育厅项目:汽车类特大型厚板成型模开发实践（201203Y13196）

林泉 (1973-)，女，硕士，讲师

参考文献：

[1]胡兆国，朱超，冷祯龙. 分离器冲压工艺及模具设计[J]. 锻压技术，2014，39（6）：105-109.

Hu Z G，Zhu C，Leng Z L. Study of the stamping process and the mold design for separator [J]. Forging & Stamping Technology，2014，39（6）：105-109.

[2]张晓达，陈金香，李洪波. 基于多工位成形机床的缩口成形零件的模具设计[J]. 锻压技术，2014，39（8）：81-85.

Zhang X D，Chen J X，Li H B. Die design for shrinkage mouth molding parts based on multi-position forming lathe [J]. Forging & Stamping Technology，2014，39（8）：81-85.

[3]朱超，胡兆国，曹素兵. 支架冲压工艺及模具设计研究[J]. 锻压技术，2014，39（7）：58-65.

Zhu C，Hu Z G，Cao S B. Study of stamping process and mold design of stand [J]. Forging & Stamping Technology，2014，39（7）：58-65.

[4]何鹏申，刘春雨，郑薇，等.某车型行李箱盖包边模设计[J]. 锻压技术，2014，39（10）：52-57.

He P S，Liu C Y，Zheng W，et al.Design on hemming dies of an automobile trunk lid [J]. Forging & Stamping Technology，2014，39（10）：52-57.

[5]钟江静，梁士红.接触簧片冲压工艺及模具结构设计[J].锻压技术，2013，38(4)：106-110.

Zhang J J, Liang S H. Design of stamping process and die structure for contact spring[J]. Forging & Stamping Technology, 2013,38(4):106-110.

[6]陈世涛，阮林凡，赵淮北. 带气动切换机构的汽车顶盖翻边整形模设计[J].锻压技术,2013，38(4):101-105.

Chen S T, Ruan L F, Zhao H B. Design of automotive roof flanging-sizing mold with pneumatic switching mechanism[J]. Forging & Stamping Technology, 2013，38(4): 101-105.

[7]向小汉. 侧围外板冲压工艺分析[J]. 热加工工艺,2013,42（1):78-81.

Xiang X H.Analysis of stamping process for side wall outer panel [J]. Hot Working Technology,2013,42（1):78-81.

[8]付明杰，许慧元，邵杰，等. TA15钛合金板材单向拉伸超塑变形行为研究[J].稀有金属, 2013, 37(3): 353-358.

Fu M J, Xu H Y, Shao J, et al. Superplastic deformation rehavior of TA15 alloy sheet by superplastic tension[J].Chinese Journal of Rare Metals, 2013，37(3): 353-358.

[9]周雄新，欧笛声. 基于CAD/CAE汽车大地板外侧梁拉延模设计[J].锻压技术, 2013, 38 (1) : 133-136.

Zhou X X，Ou D S. Drawing die design of automobile floor lateral beam based on CAD/CAE[J]. Forging & Stamping Technology, 2013, 38 (1): 133-136.

[10]钟江静，梁士红. 接触簧片冲压工艺及模具结构设计[J]锻压技术, 2013, 38 (4):106-110.

Zhong J J，Liang S H.Design of stamping process and die structure for contact spring [J]. Forging & Stamping Technology, 2013, 38 (4): 106-110.

服务与反馈：

【文章下载】【加入收藏】