锻压技术

精冲技术的研究现状与发展趋势

英文标题：Current research and development tendency of fine blanking technology

作者：夏琴香胡玄通陈登曲洪波

分类号：

出版年,卷(期):页码：2015,40(7):1-6

摘要：

本文从精冲机理、精冲工艺、精冲方法、精冲过程有限元模拟方法、精冲模具以及精冲设备这6个方面对精冲技术进行了综述，介绍了精冲技术在以上几个方面的研究现状。分析结果表明，目前对精冲技术的研究主要集中在精冲机理、精冲工艺、精冲设备等方面，对精冲模具、精冲方法、精冲过程有限元模拟方法等方面的研究还较欠缺；高强度材料及复杂结构零件的精冲生产是目前精冲技术的难点；提出了采用创新的精冲方法、高复合度的精冲复合工艺以及智能化的精冲模具将是精冲技术未来的发展趋势。

It was discussed comprehensively the fine blanking technology by analyzing the mechanism, the process, the method, the finite element simulation, the die and the equipment of the fine blanking. The current research status from the six aspects above was reviewed. The results show that the current researches are mainly focused on the mechanism, the process and the equipment of fine blanking, while the researches on the method, the finite element simulation and the die of fine blanking are insufficient. Producing fine blanking parts with high-strength materials and complex structure is the difficulty of the current fine blanking technology. It is proposed that the innovative fine blanking method, the fine blanking combination process of high integration level, and the intelligent fine blanking die are the development trend of fine blanking.

基金项目：

广东省中科院全面战略合作项目（2012B091100251）

夏琴香（1964-），女，博士，教授

参考文献：

[1]涂光祺. 精冲技术[M]. 北京：机械工业出版社, 2006.

Tu G Q. Fine Blanking Technology [M]. Beijing：China Machine Press，2006.

[2]黄毅宏, 黎厚芳. 精冲工艺及其机理探讨[J]. 中国机械工程, 1994, 5(5): 57-59.

Huang Y H, Li H F. A study on the fine blanking process and its mechanism [J]. China Mechanical Engineering, 1994, 5(5): 57-59.

[3]Lee T C, Chan L C, Wu B J. Further investigation of the fine-blanking process employing large deformation theory[J]. Journal of Materials Processing Technology, 1997, 66(1): 258-263.

[4]邓明, 夏庆发, 杜丽伟. 基于变形区显微状态分析的精冲成形机理研究[J]. 塑性工程学报, 2006, 12(6): 71-73.

Deng M, Xia Q F, Du L W. Research on fine-blanking mechanism based on analyzing microstate of deformation zone[J]. Journal of Plasticity Engineering, 2006, 12(6): 71-73.

[5]Thipprakmas S, Jin M, Murakawa M. An investigation of material flow analysis in fineblanking process[J]. Journal of Materials Processing Technology, 2007, 192: 237-242.

[6]温莉敏, 王贤才, 李琴,等. 反压力与精冲质量的关系研究[J]. 淮海工学院学报, 2013, 22(2): 18-21.

Wen L M, Wang X C, Li Q,et al. Relationship between counter force and fine-blanking quality [J]. Journal of Huaihai Institute of Technology, 2013, 22(2): 18-21.

[7]Kwak T S, Kim Y J, Bae W B. Finite element analysis on the effect of die clearance on shear planes in fine blanking[J]. Journal of Materials Processing Technology, 2002, 130: 462-468.

[8]Thipprakmas S. Application of Taguchi technique to investigation of geometry and position of V-ring indenter in fine-blanking process[J]. Materials & Design, 2010, 31(5): 2496-2500.

[9]Thipprakmas S. Finite-element analysis of V-ring indenter mechanism in fine-blanking process[J]. Materials & Design, 2009, 30(3): 526-531.

[10]袁贺强, 彭群, 涂光祺, 等. 往复成形精冲技术的研究[A]. 第八届全国塑性加工学术年会论文集[C].北京， 2002.

Yuan H Q, Peng Q, Tu G Q. Study on reciprocating fine blanking technology[A]. Proceedings of The Eighth National Plastic Processing Symposium[C].Beijing, 2002.

[11]邓明, 张会杰, 吕琳，等. 闭挤式精冲工艺及其成形规律[J]. 锻压技术, 2009, 34(6): 39-41.

Deng M, Zhang H J, Lv L，et al. Reach on process of closed extruding fine-blanking and material flowing rule[J]. Forging & Stamping Technology, 2009, 34(6): 39-41.

[12]Fan W F, Li J H. An investigation on the damage of AISI-1045 and AISI-1025 steels in fine-blanking with negative clearance[J]. Materials Science and Engineering: A, 2009, 499(1): 248-251.

[13]Thipprakmas S, Rojananan S, Paramaputi P. An investigation of step taper-shaped punch in piercing process using finite element method[J]. Journal of Materials Processing technology, 2008, 197(1): 132-139.

[14]Zhao Z, Zhuang X C, Xie X L. An improved ductile fracture criterion for fine-blanking process [J]. Journal of Shanghai Jiaotong University (Science), 2008,13(6):702-706.

[15]张杰. 精冲断裂裂纹扩展有限元算法研究[D]. 上海：上海交通大学, 2007.

Zhang J. Research on Algorithm of FEM Simulation of Crack Propagation in Fine-blanking [D].Shanghai： Shanghai Jiao Tong University, 2007.

[16]谢晓龙, 赵震, 虞松,等. 基于 Oyane 损伤和断裂模型的厚板精冲过程数值模拟和缺陷预测[J]. 上海交通大学学报, 2006, 40(6): 927-931.

Xie X L, Zhao Z, Yu S,et al. The numerical simulation and failure prediction for thick sheet metal fine-blanking based on Oyane damage and fracture mode [J]. Journal of Shanghai Jiao Tong University (Science), 2006, 40(6): 927-931.

[17]邓明, 黄伟九, 何西平. 精冲模具的磨损及断裂研究[J]. 现代制造工程, 2004,(3): 15-16.

Deng M, Huang W J, He X P. Study on the wear and fracture of fine blanking die [J]. Modern Manufacturing Engineering, 2004, (3): 15-16.

[18]朱彦生. 基于有限元分析的精冲凸模寿命估算[D]. 武汉: 武汉理工大学, 2007.

Zhu Y S. The Lifetime Estimation of Fine-blanking Male-die based on FEM Analysis [D]. Wuhan:Wuhan University of Technology, 2007.

[19]王海洋. 模具材料及表面涂层对精冲模具寿命的影响研究[D].武汉：华中科技大学, 2012.

Wang H Y. Study of Fine Blanking Die Life under the Influence of Tool Steel and Surface Coatings [D]. Wuhan：Huazhong University of Science and Technology, 2012.

[20]左传付, 李聚群, 杨晓红,等. 循环超细化热处理提高精冲模具寿命的研究[J]. 金属热处理, 2008, 33(4): 47-49.

Zuo C F, Li J Q, Yang X H,et al. Life improvement of precision punching die with cyclic super-fine heat treatment [J]. Heat Treatment of Metals, 2008, 33(4): 47-49.

[21]甘瞾. 棘轮精冲模具设计与动力学分析[D]. 武汉：华中科技大学, 2009.

Gan Z. Fine Blanking Die Design & Dynamic Simulation of Ratchet Wheel [D].Wuhan： Huazhong University of Science and Technology,2009.

[22]王磊. 曲柄精冲工艺研究及模具结构优化[D]. 武汉：华中科技大学, 2009.

Wang L. Research on Fine Blanking Process of Crank and Optimization of Die Structure [D]. Wuhan：Huazhong University of Science and Technology, 2009.

[23]曹传亮, 张祥林, 董春法, 等. 精冲模具在冲压过程中的温升研究[J]. 锻压技术, 2014,39（7）: 113-117.

Cao C L, Zhang X L, Dong C F,et al. Study of die temperature rising in fine blanking process[J]. Forging & Stamping Technology, 2014, 39（7）: 113-117.

[24]李艳霞, 邓明, 吕琳. 精冲机的现状及发展趋势[J]. 锻压装备与制造技术, 2008, 43(1): 15-17.

Li Y X, Deng M, Lv L. Status and development of fine blanking press[J]. China Metal Forming Equipment, 2008, 43(1): 15-17.

[25]黄重九, 杨帅帅, 陈渊, 等. 大吨位全自动液压精冲机的研制[J]. 机床与液压, 2011, 39(18): 1-3.

Huang C J, Yang S S, Chen Y,et al. Research and manufacture of large-tonnage automatic hydraulic fine-blanking press[J]. Hydromechatronics Engineering，2011, 39(18): 1-3.

[26]刘艳雄，华林,张勇，等. 汽车零件复合精冲成形技术与装备[A].第七届中国精冲技术研讨会论文集[C].武汉，2011.

Liu Y X, Hua L，Zhang Y,et al. The composite fine blanking technology and equipment of car parts[A]. Symposium of Seventh Chinese fine blanking technology Seminar[C].Wuhan,2011.

[27]Gram M D, Wagoner R H. Fine blanking of high strength steels: Control of material properties for tool life[J]. Journal of Materials Processing Technology, 2011, 211(4): 717-728.

[28]Yang S, Song Y, Zhang M. Effects of parameters on rotational fine blanking of helical gears[J]. Journal of Central South University, 2014, 21: 50-57.

[29]Zimmermann M, Klocke F, Schongen F, et al. Fine blanking of helical gears-finite element simulations and first experimental results [J]. Steel Research International, 2011,(Special Edition): 581-585.

[30]Yang S, Hua L, Song Y L. Numerical investigation of fine blanking of a helical gear[J]. Applied Mechanics and Materials, 2012, 190: 121-125.

[31]Klocke F, Zimmermann M, Backer V, et al. Finite element simulation of an analogy process for the fine blanking of helical gears[A].Assembly and Manufacturing (ISAM), 2011 IEEE[C].Tampere,2011.

[32]李雪松, 陈军, 吴公明，等. 汽车离合器衬套冲锻复合工艺研究及其数值模拟[J]. 锻压装备与制造技术, 2006, 41(1): 49-51.

Li X S, Chen J, Wu G M，et al. Research of stamping-forging composite process of automobile clutch bush and its numerical simulation [J]. China Metal Forming Equipment, 2006, 41(1): 49-51.

[33]Kim H S. A study on cold forging process sequence design of terminal pins for high-voltage capacitors [J]. Journal of Materials Processing Technology, 2007, 187: 604-608.

[34]钟莫.专家提出优先发展智能模具[N]. 中国工业报, 2011-03-07(B03).

Zhong M. The Expert Proposes to Give Priority to the Development of Intelligent Mould [N]. China,Industry News, 2011-03-07(B03)

[35]李孟源，尚振东，蔡海潮，等.声发射检测及信号处理[M]. 北京：科学出版社, 2010.

Li M Y,Shang Z D,Cai H C,et al. Acoustic Emission Detection and Signal Processing [M].Beijing: Science Press, 2010.

[36]潘智鹏, 陈鹏, 曹传亮, 等. 声发射在精冲模具崩刃在线检测中的应用[J]. 无损检测, 2012, 34(9): 30-33.

Pan Z P, Chen P, Cao C L,et al. The application of the acoustic emission in the online detection of fine blanking mold chipping [J]. Nondestructive Testing, 2012, 34(9): 30-33.

服务与反馈：

【文章下载】【加入收藏】